Trackwork

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Trackwork

Postby ScaleCraft » Tue Nov 20, 2018 8:45 pm

That is why THIS layout will come apart easily. Ballast, loose. Shopvac.
Track screwed down....not glued down. Switches screwed down. Groundthrows screwed down.
No nails in the benchwork (or even slot-head screws like one I tore down).
Dave....gone by invitation

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Trackwork

Postby ScaleCraft » Sat Nov 24, 2018 4:38 pm

J. S. Bach wrote:Well, if you ever want to get rid of the Quonset hut.................. Seriously, I eagerly await the photos.

https://korbermodels.com/collections/o-scale?page=3
Kit 706.
Not the straight sided one shown, but a round-roof-to-the-ground unit. Buy two or three! Kit bash!
Dave....gone by invitation

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Trackwork

Postby Rufus T. Firefly » Sat Nov 24, 2018 5:28 pm

ScaleCraft wrote:No nails in the benchwork (or even slot-head screws like one I tore down).


So what holds the benchwork together? No nails, no screws.....friction and gravity? Dovetails?
Last edited by Rufus T. Firefly on Sat Nov 24, 2018 6:11 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Trackwork

Postby ScaleCraft » Sat Nov 24, 2018 5:49 pm

Rufus T. Firefly wrote:
ScaleCraft wrote:No nails in the benchwork (or even slot-head screws like one I tore down).


So what holds the benchwork together? No nails, no screws.....friction and gravity?


Ah, read and understand, padawan.
No Nails. No slot-head screws.
Does not eliminate Phillips head screws.

Slot head...geez. Joe (Mensa, no less) did all 3/4 ply benchwork, including "L" cross section legs...and slot head screws. Probably thousands of the buggers.

SOMEbody robbed every tool out of the place before we tore it down....but, in the bottom of a drawer of junk was a cut off slot head screwdriver that fit up in the old Makita drill chuck.

Good thing about him being an anal-retentive Mensa, is the screws straight down through the top sheet of 3/4 ply into the 3/4 ply side sheets...and covered with scenery...were all spaced exactly the same distance apart on all the module sections so we didn't have to chisel out 8 feet of plaster to find the screw heads.
Dave....gone by invitation

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Trackwork

Postby Rufus T. Firefly » Sat Nov 24, 2018 6:15 pm

ScaleCraft wrote:
Rufus T. Firefly wrote:
ScaleCraft wrote:No nails in the benchwork (or even slot-head screws like one I tore down).


So what holds the benchwork together? No nails, no screws.....friction and gravity?


Ah, read and understand, padawan.
No Nails. No slot-head screws.
Does not eliminate Phillips head screws.


Or a host of other types of screws - I was reading that as your disdain of screws in general. I figured you used blind dovetail joints, :lol: :lol: :lol: :lol: :lol:

Slot head...geez. Joe (Mensa, no less) did all 3/4 ply benchwork, including "L" cross section legs...and slot head screws. Probably thousands of the buggers.


Probably got a good deal on a case of them - beats dealing with glue dipped nails - yes, I've had the joy of dealing with a layout assembled using them. Crowbars, striking hammer, and sawzall....
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 34 guests