Page 1 of 2
ATSF Panel-Side Automobile Boxcar
Posted: Fri Dec 01, 2017 12:42 pm
by R.K. Maroon
A friend recently sent me this very nice model of a 50' panel-side double-door ATSF automobile car:

- Auto Box ATSF 67215.JPG (73.57 KiB) Viewed 6805 times
The car is dated 1968. It is of unusual construction. The roof and floors are wood. The sides are wood with what looks like a very thin resin overlay. The doors and ends are cast resin. I know that Zimmer and Suncoast both offered 40' ATSF panel-side boxcars, but I am unaware of a kit like this. As far as I know, the Cooch kits were all resin, and I don't recall them offering this car. Any clues? The car is darker than it looks, but I have lightened it up in the photo to show the detail better. The car needs a little TLC but is otherwise serviceable and will provide a nice complement to all those Athearn ATSF auto cars currently on the local club's roster.
Jim
Re: ATSF Panel-Side Automobile Boxcar
Posted: Fri Dec 01, 2017 1:05 pm
by Jay Criswell
FWIW, Zimmer did a 50" also. Not saying that's what you have just correcting the record.
How about a photo of the bottom?
Jay
Re: ATSF Panel-Side Automobile Boxcar
Posted: Fri Dec 01, 2017 1:23 pm
by R.K. Maroon
Thanks, Jay -- I did not know about the 50' Zimmer. Here is a shot of the bottom.

- Auto Box ATSF 67215 -- Bottom View.JPG (45.84 KiB) Viewed 6795 times
Nothing fancy: Athearn metal trucks, fixed couplers.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Fri Dec 01, 2017 9:03 pm
by bob turner
Hot digs! I have one. Lobaugh. Photos manana.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Fri Dec 01, 2017 10:15 pm
by Jay Criswell
Bob,
I was going to mention the Lobaugh but Jim says this model has resin doors and ends. Don't think Rollin was big on resin.
Jay
Re: ATSF Panel-Side Automobile Boxcar
Posted: Sat Dec 02, 2017 12:09 am
by R.K. Maroon
You guys are good -- Lobaugh did indeed make this car:

- Lobaugh ATSF FeV.png (369.49 KiB) Viewed 6730 times
Note the rivets in the spaces between the panels, missing on my model. Other details don't quite match either, like door hardware. Here's the description:

- Lobaugh ATSF FeV Text.png (116.21 KiB) Viewed 6730 times
No pressed metal on mine. Also note that if you were to have bought the car factory-built from Lobaugh it would have arrived hand-lettered. The decals were only available to the lesser rich guys that could only afford kit. That seems preposterous now but what goes around comes around. Hand-lettered was apparently prized more than decals then, and if you listed one each from the era on eBay now, the hand-lettered one would again bring a higher price. The value holds in another way too -- I would say from my limited experience that a high percentage of hand-lettered cars from that era still have lettering that looks good today, but only a low percentage of decaled cars from the same era still have the decals intact. No, I don't have data to back that up.
Jim
Re: ATSF Panel-Side Automobile Boxcar
Posted: Sat Dec 02, 2017 5:30 pm
by J. S. Bach
R.K. Maroon wrote: ...snip... I would say from my limited experience that a high percentage of hand-lettered cars from that era still have lettering that looks good today, but only a low percentage of decaled cars from the same era still have the decals intact. No, I don't have data to back that up. Jim
Paint vs decal film. Plus, the shellac (or whatever) that was sometimes applied to "seal" the decal has degenerated over the years.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Sun Dec 03, 2017 9:40 pm
by Erik C Lindgren
The markings are absolutely identical to the DSMR marked cars I’ve had many encounters with over the last 15 years. It looks like either Calahan’s (50’s later into 80’s) hand writing or maybe even Kennedy (wayback to 1940’s). They used to mark them on each inspection that included “lub” or “gaged”... 6/68, 4/54, 3/39 etc. Lovey specimen man!! If in fact it’s an ex-Denver Society car that’s a neat bunch of history dating to the 1930’s.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Mon Dec 04, 2017 6:49 pm
by bob turner
Here is mine - genuine Lobaugh with stamped brass doors and ends. A nice model. Cannot find the matching ice car.

- DSC02533.JPG (909.16 KiB) Viewed 6601 times
Re: ATSF Panel-Side Automobile Boxcar
Posted: Mon Dec 04, 2017 7:34 pm
by Jay Criswell
Interesting. The prototype doesn't have rivets down the center of the channel separating the panels. Somebody's imagination or just artistic license?
Jay
Re: ATSF Panel-Side Automobile Boxcar
Posted: Sat Dec 09, 2017 7:37 pm
by Jay Criswell
Re: ATSF Panel-Side Automobile Boxcar
Posted: Sun Dec 10, 2017 12:04 am
by R.K. Maroon
Thanks for posting the photos, Jay. I was aware of both versions but don't know enough about the prototypes to know that the A-N car was not correctly proportioned. It is tall, though -- that's for sure:

I believe I have one of the Suncoast models, but I also have one or two scratchbuilt versions -- I will dig them out and post photos as I can.
Jim
Re: ATSF Panel-Side Automobile Boxcar
Posted: Tue Jan 16, 2018 9:34 pm
by R.K. Maroon
I stumbled onto this photo hiding in my files today:

- Suncoast ATSF Panel Box Car Kit.JPG (163.62 KiB) Viewed 6424 times
I think I have the actual model too. With luck I will stumble on that as well.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Wed Jan 17, 2018 12:17 pm
by sarge
Jim
They are nice kits; I've done several over the years. At one time if memory serves, Woody Grosdof owned Suncoast and made those kits, still available in the 90s. They came in two versions, one as built with K-brakes and the earlier reporting mark on the decals and a modernised version without the periods on the reporting mark and different brakegear.
Jay, a question for you. Were there not several different classes of panelside boxcar? I seem to remember (wrongly probably, since my memory has been pretty faulty lately) there was a car done by ATSF to either the '32 or '37 AAR design but with panel sides rather than steel (perhaps even wartime?) much in the same manner GN did with their own style of wooden cladding, and the Zimmer was at least close as a 10' 6" IH version. I could easily be 'way wrong, but I did run a Zimmer on my old layout for years under those (suspect) premises, one that Ted Stepek originally built.
Re: ATSF Panel-Side Automobile Boxcar
Posted: Wed Jan 17, 2018 1:57 pm
by Jay Criswell
Sarge,
I have a book here somewhere that provides most, if not all, of the data. Truthfully, I don't recall the specifics.
Yeah, I have a bunch of the Sun Coast kits. Some started, some still in kit form. Four or five Zimmers too. A couple of those were started but need to be taken back apart because some of the pieces were installed poorly. Maybe some ambitious soul will take up the challenge.....I don't seem to have the time.
Jay