Page 1 of 4

Another interesting item...........

Posted: Fri Dec 08, 2017 8:10 am
by herronpeter
.........which is a "mystery"!!!!!!!!

https://www.ebay.com/itm/All-Brass-Myst ... SwIVhaKTLX

Peter

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 8:14 am
by Rufus T. Firefly

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 10:14 am
by sarge
Rufus T. Firefly wrote:Perhaps even more interesting:

https://www.ebay.com/itm/O-SCALE-STEAME ... 0005.m1851


Polydrive?

I've actually never seen one complete in the flesh (lucky me in over fifty years of O scale!), so its a guess.

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 11:04 am
by Jay Criswell
Yeppers! That's a Walther's 0-6-0 w/Polydrive. I have most of the pieces (including the superstructure) for their 4-8-2 but the plastic in the center of the drivers is crumbling.

Some feel these drives would/will never operate well but I think it could be done. The secret would be better drive components and getting the drivers lined up properly (like the timing of a DOHC engine).

While examining the 4-8-2 I came away with the opinion it might be 17/64". It just looked larger than I thought it should.

Jay

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 1:15 pm
by Carey Williams
Hello Poly People

1940 Bill Walthers makes a big splash with his introduction of snap together drive trains ... fully covered in the 1940 catalog ... claiming that the engines he provided for the 1939/40 World's Fair were equipped the Poly drive ...
Below photos of the 1940 Walthers catalog .... a photo of the poly drive stolen from the http://WWW...and a photo of my Mikado with Poly Drive .... it runs after a fashion ...Walthers strong hand was never engines ( in my opinion) .....however I'm liking the stream-liner ..has anyone ever seen one of these ? it was carried in the catalog for several years ...all cast body ...there has to be a pile of them somewhere ...

1/4" or 17/64ths ? ....the Mikado leans more 1/4" ...
Jay can you please post photo of your Northern ?

Cheers Carey

IMG_6903.JPG
IMG_6903.JPG (2.25 MiB) Viewed 8519 times




IMG_6904.JPG
IMG_6904.JPG (2.37 MiB) Viewed 8519 times


polymor drive units 1940.jpg
polymor drive units 1940.jpg (379.53 KiB) Viewed 8519 times


IMG_6891.JPG
IMG_6891.JPG (1.53 MiB) Viewed 8519 times

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 1:57 pm
by Jay Criswell
Carey,

Next time I go by the storage unit I'll see if I can find them (boiler in one box, mechanism in another). BTW, I think it's a Mountain.

Jay

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 2:04 pm
by bob turner
Lionel used that general idea for years. My little (? -17/64?) B6 0-6-0 runs fine with all drivers geared together.

Re: Another interesting item...........

Posted: Fri Dec 08, 2017 11:20 pm
by Carey Williams
Hello Jay ...storage unit .... I thought trains were suppose to be on a layout running past your fine Model Structures buildings ....thank you for hunting down the bits for photographic documentation

Hello Bob ....you have a Poly drive 060 ? or a Lionel 060 ? ..... yes the Lionel 060 certainly seems at least 17/64ths as it towers over the little 700E ... Lionel always made such big deal promoting their use of scale .... they failed to use the "same" scale on any two models ... details

If you have a Walthers 060 please post a photo for the world to gaze at it's beauty .
Cheers Carey

Re: Another interesting item...........

Posted: Sat Dec 09, 2017 8:55 am
by herronpeter
Hey Rufus,

Yours ended up being more interesting than mine! I'm crushed.............I'm going home and taking my ball with me!!

Peter

Re: Another interesting item...........

Posted: Sat Dec 09, 2017 7:21 pm
by robert.
this auction goes off tomorrow. not much if any 2 rail.
http://www.auctionzip.com/auction-catal ... &keywords=

Re: Another interesting item...........

Posted: Sat Dec 09, 2017 7:30 pm
by Jay Criswell
May just be the absolute zenith in basket cases!

Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

Jay

Re: Another interesting item...........

Posted: Sun Dec 10, 2017 12:32 am
by Carey Williams
Thank you very much Jay for documenting your Poly Walthers ..... it is a big engine ....once all put together ....

Those plastic drivers did not hold up for the durability tests ...

Cheers Carey

Re: Another interesting item...........

Posted: Sun Dec 10, 2017 10:09 am
by Rufus T. Firefly
herronpeter wrote:Hey Rufus,

Yours ended up being more interesting than mine! I'm crushed.............I'm going home and taking my ball with me!!

Peter


When I saw the polydrive, yup!

Re: Another interesting item...........

Posted: Sun Dec 10, 2017 5:23 pm
by herronpeter
My opinion of the Polydrive (bearing in mind I’m way to young in O scale to have ever seen one) is that you multiply the noise from one old gear box time 4 for a real coffee grinder sound. All that complexity just to get plastic drivers. Makes no sense to me and others if the modern practice of one gear box per one steam locomotive is any measure.

Peter

Re: Another interesting item...........

Posted: Sun Dec 10, 2017 5:30 pm
by Rufus T. Firefly
herronpeter wrote:My opinion of the Polydrive (bearing in mind I’m way to young in O scale to have ever seen one) is that you multiply the noise from one old gear box time 4 for a real coffee grinder sound. All that complexity just to get plastic drivers. Makes no sense to me and others if the modern practice of one gear box per one steam locomotive is any measure.


My opinion is limited to this being a historical curiosity item, :wink: :wink: