.
Re: Old Rivets & The FOM
2RailJon,
When these Sunset 3rd Rail GG-1 models first arrived I was asked by several modelers who purchased them to go over them. I found that the frames were bent and keeping the drivers off of the rails. I managed to straighten the frames by putting a wooden pencil between the car body and the frame at an appropriate location and gently bending the frame using the pencil as a fulcrum. This was a quick fix and improved the operation of these models.
I do not have a high opinion of these locomotives. Look at your frame closely. This may be the problem with your loco.
Joe
When these Sunset 3rd Rail GG-1 models first arrived I was asked by several modelers who purchased them to go over them. I found that the frames were bent and keeping the drivers off of the rails. I managed to straighten the frames by putting a wooden pencil between the car body and the frame at an appropriate location and gently bending the frame using the pencil as a fulcrum. This was a quick fix and improved the operation of these models.
I do not have a high opinion of these locomotives. Look at your frame closely. This may be the problem with your loco.
Joe
Joe Foehrkolb
Re: Old Rivets & The FOM
.
Last edited by 2railjon on Sun May 27, 2018 5:45 pm, edited 1 time in total.
Running that red block Charlie.
-
bob turner
- Posts: 13675
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Old Rivets & The FOM
I do have a high opinion, but think they need all six axles powered. Ditto the FF2.
Re: Old Rivets & The FOM
2RailJon.
I also remember shortening the length of the springs under the pilot truck mounting screws. The pilot trucks seemed to be lifting the drivers off of the track.
I never had to disassemble these models. I just slid the pencil between the car body bottom and the frame that holds the drive assembly.
Bob T. IMO These are very nicely done car bodies with lousy drives using cheap motors and all wheels should have been powered.
Joe
I also remember shortening the length of the springs under the pilot truck mounting screws. The pilot trucks seemed to be lifting the drivers off of the track.
I never had to disassemble these models. I just slid the pencil between the car body bottom and the frame that holds the drive assembly.
Bob T. IMO These are very nicely done car bodies with lousy drives using cheap motors and all wheels should have been powered.
Joe
Joe Foehrkolb
Re: Old Rivets & The FOM
.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.
Re: Old Rivets & The FOM
See if that unpowered main axle isn't oversupporting as well; bloody stupid design having the pilot trucks and an unpowered wheel on opposite ends oversupporting the two driven ones. You'll have to treat each assembly as you would sorting a poorly sprung 4-4-2 steam loco.
Also, the weight is conveniently where it does the least good, over two undriven axles. Can you get some sheet lead under the motors and over the driven axles?
Also, the weight is conveniently where it does the least good, over two undriven axles. Can you get some sheet lead under the motors and over the driven axles?
-
bob turner
- Posts: 13675
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Old Rivets & The FOM
Sprockets and Delrin chain.
Re: Old Rivets & The FOM
.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.
Re: Old Rivets & The FOM
Can you fill the shell with shot and epoxy
I spend entirely too many hours a day tying my shoes
Re: Old Rivets & The FOM
.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.
Re: Old Rivets & The FOM
Jon, if you've never done that stunt before, don't be tempted to use white glues or carpenters glue (PVA) with shot. I've seen many a model ripped apart as the mass swells pretty friskily over a long period of time.
- Rufus T. Firefly
- Posts: 42220
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Old Rivets & The FOM
Can you fill the shell with shot and epoxy
sarge wrote:Jon, if you've never done that stunt before, don't be tempted to use white glues or carpenters glue (PVA) with shot. I've seen many a model ripped apart as the mass swells pretty friskily over a long period of time.
If wanted, I could send you an ingot of Cerrobend to reshape to where it might fit. I might also find it possible to scrounge up some sheet lead.
Let me know, Jon
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Old Rivets & The FOM
.
Last edited by 2railjon on Sun May 27, 2018 5:47 pm, edited 1 time in total.
Running that red block Charlie.
- rex desilets
- Posts: 1786
- Joined: Sun Jul 15, 2007 2:18 pm
Re: Old Rivets & The FOM
Amazon.comRufus T. Firefly wrote:<snip> I might also find it possible to scrounge up some sheet lead.
<snip>
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” – John Adams
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 38 guests