Page 1 of 2

New Mold

Posted: Sun Dec 23, 2018 5:20 pm
by Jay Criswell
I've been wanting to redo my 1:1 brass gearboxes for a long time. Lucky for me I have some talented friends. Jim Read did all the computer drawings, Terry Van Winkle verified they would work with his printer...and they did so he made a series of very fine resolution prints, destined to become masters. He handed off the new patterns to a shop in NY and they made a low shrink RTV mold. They shot four waxes and used them to cast four test shots in bronze. The bronze always looks mottled but when these are done in yellow brass by Valley Brass & Bronze (David Sciacca) they will look much nicer. So far, I'm very happy with the results.

Thank you for the help Jim & Terry. Obviously I couldn't have done it without you.

2018-12-20 006.JPG
2018-12-20 006.JPG (1.35 MiB) Viewed 7487 times
2018-12-20 005.JPG
2018-12-20 005.JPG (1.38 MiB) Viewed 7487 times
2018-12-20 004.JPG
2018-12-20 004.JPG (1.35 MiB) Viewed 7487 times
2018-12-20 002.JPG
2018-12-20 002.JPG (2.61 MiB) Viewed 7487 times


Jay

Re: New Mold

Posted: Sun Dec 23, 2018 5:47 pm
by sleepmac
Jay, beautiful!

Dan Weinhold

Re: New Mold

Posted: Sun Dec 23, 2018 6:30 pm
by E7
I'll second Dan's comment!

Rich

Re: New Mold

Posted: Sun Dec 23, 2018 9:49 pm
by stephen neill
Keep on keeping on Jay. They look great. We will of course want to know more as things continue to progress.
Steve

Re: New Mold

Posted: Mon Dec 24, 2018 4:45 pm
by PRR Man
nice, nice... very nice.

Re: New Mold

Posted: Tue Dec 25, 2018 12:41 pm
by Jay Criswell
Thanks Guys,

The way things look these are going to be far easier to prep (machine) for assembly.

Dropped the mold off at the foundry yesterday and asked David to cast up 40 or so. If they work out as well as they should I'll have him do another 100. That should last a while.

Jay

Re: New Mold

Posted: Tue Dec 25, 2018 12:45 pm
by stephen neill
In my best Rufus imitation: You DROPPED it? I hope it didn't break.

Thanks for the update.

Merry Christmas to all.

Steve

Re: New Mold

Posted: Tue Dec 25, 2018 1:36 pm
by Jay Criswell
It's rubber, like some checks, it will bounce.

Re: New Mold

Posted: Tue Dec 25, 2018 9:59 pm
by cole7015
Jay do you have price figures on these yet?

Bill Basden Delta Models www.deltamodelsusa.com

Re: New Mold

Posted: Tue Dec 25, 2018 11:26 pm
by Jay Criswell
Bill,

Same price I've been charging. $55.00 with customers choice of wheels (P:48 or O Scale, 30" to 42"). Input/output included.

The time consuming part is making the axles and input/output shafts. Actually, it's not making them that's time consuming, it's getting the correct dimensions. Axles and input/output are custom made to fit the customer's needs.

Jay

Re: New Mold

Posted: Wed Dec 26, 2018 2:02 pm
by R.K. Maroon
Jay -- Thank you for providing the photos and an explanation of the number of steps involved in the process. It seem like quite an investment of time, effort, and (I imagine) cost.

Two questions:

1. Did you have an "old mold" to do these or were they previously hogouts?'

2. I have always been curious as to how one machines the two bores in such a gearbox. Specifically, do you establish a datum surface, such as one of the outside flat surfaces of the case, to serve as a reference for machining both shaft bores, or is there some clever way to directly locate the second bore to the first bore?

Jim

Re: New Mold

Posted: Wed Dec 26, 2018 10:23 pm
by Jay Criswell
Jim,

The old masters were hand made buy lacking the accuracy I desired. The molds made from these masters carried the flaws right into the castings. The machining required to make them acceptable was way too time consuming. Yes there was tooling and fixtures used to hold them in place while they were drilled, milled, tapped, etc.

The new masters were made using 3d printing. No, not the Shapeways crap. The machines used for this are the high end models with very fine resolution. The resulting master require very little machining. Drilling and tapping are still needed. High speed burrs and 6 flute end mills are used for any minor clean up.

Jay

Re: New Mold

Posted: Thu Dec 27, 2018 1:29 am
by Jay Criswell
Jim,

I suppose that was a rather lame reply. I'll see if I can come up with something a little more in depth.

Jay

Re: New Mold

Posted: Thu Dec 27, 2018 6:56 pm
by big bad jim
The boxes are looking good Jay. It's always nice to see things come to fruition. You should bring an example along to Chicago so that I can check them out in person.

Jim

Re: New Mold

Posted: Thu Dec 27, 2018 7:09 pm
by bob turner
I thought it was a pretty good explanation. Lost wax can be pretty accurate if your masters are ok.