Page 1 of 1
Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 4:59 pm
by 2railjon
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:21 pm
by E7
They were probably thinking: I'm not the poor sap who is going to be messing with these, so I don't care how big a PITA it is. My inclination would be, once one light went out, to rewire it for 2 maybe 3 bulbs or maybe better yet LED's! That might be a thought: once one goes put in LED's.

How bright do the interiors have to be anyhow?
Rich
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:35 pm
by Rufus T. Firefly
E7 wrote:They were probably thinking
Stop right there. They weren't.
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:46 pm
by big bad jim
Not trying to be a smartass here, but is it possible that you are only supposed to switch the coupler, installing the Kadee in the existing box? I've no idea what the factory coupler box cover looks like. But the instructions do only mention to switch the coupler, and also claim that it will be simple, which sounds distinctly different to cutting and shaping Kadee coupler boxes as you have.
Jim
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:47 pm
by E7
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:50 pm
by E7
Mitch, would you care to weigh in on this one?

Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:54 pm
by 2railjon
LOL, Rich and Rufus! They won’t be any shelf relics. I plan to run and enjoy them! When a bulb goes out, it’s LED strip time. Will it decrease the resale value? That’s my wife’s problem, I’ll be dead.

Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 5:59 pm
by 2railjon
Jim, this is how the couplers factory installed looked on the cars. No factory installed coupler box anywhere to be seen!

Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 8:05 pm
by Mitch
E7 wrote:Mitch, would you care to weigh in on this one?

Nah! If designed by SAE people, the part you need to service would be turned around backwards and totally unaccessable!

Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 9:46 pm
by big bad jim
Ok, I thought maybe there was a cover that you had removed prior to taking the first picture. Thanks,
Jim
Re: Fit This Rectangle Into This Trapizoid
Posted: Sun Jan 13, 2019 11:23 pm
by E7
Mitch wrote:E7 wrote:Mitch, would you care to weigh in on this one?

Nah! If designed by SAE people, the part you need to service would be turned around backwards and totally unaccessable!

I know better than that, you are too darned good a mechanic!
Re: Fit This Rectangle Into This Trapizoid
Posted: Mon Jan 14, 2019 9:14 am
by 2railjon
My first choice was to use Protocraft couplers but I’m not sure how the cars are wired and didn’t want to deal with any shorts between the cars.

Re: Fit This Rectangle Into This Trapizoid
Posted: Mon Jan 14, 2019 7:47 pm
by E7
E7 wrote:Mitch wrote:E7 wrote:Mitch, would you care to weigh in on this one?

Nah! If designed by SAE people, the part you need to service would be turned around backwards and totally unaccessable!

I know better than that, you are too darned good a mechanic to let a little thing like that bother you!