Page 1 of 2
Rivarossi Plastic Reading Mikado?
Posted: Mon Sep 16, 2019 1:38 pm
by R.K. Maroon
Re: Rivarossi Plastic Reading Mikado?
Posted: Mon Sep 16, 2019 4:05 pm
by ScaleCraft
0-8-0, 4-4-0, 4-6-0, C-liner, Plymouth switcher.
Tying to remember, but what are the chances that's a kitbash off an 0-8-0?
BR-80 0-6-0, French Pacific 231g #696 in green livery made by Capolavori, DB V216 diesel, no mention of the Mikado
Re: Rivarossi Plastic Reading Mikado?
Posted: Mon Sep 16, 2019 5:19 pm
by Rufus T. Firefly
ScaleCraft wrote:.........what are the chances that's a kitbash off an 0-8-0?
Pretty good.
Re: Rivarossi Plastic Reading Mikado?
Posted: Mon Sep 16, 2019 8:02 pm
by bob turner
I am going to guess that it is just the 0-8-0 mechanism, and the rest is scratchbuilt in plastic. Looks pretty nice, as did the original 0-8-0.
I personally think that plastic steam in O Scale is never going to sell well.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 12:39 am
by rex desilets
I like it. Howsomever, the likely plastic chassis would relegate the model to mostly display.
Otherwise, I have nothing against plastic where properly used. But, I never learned blacksmithing, either.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 4:19 am
by E7
rex desilets wrote:I like it. Howsomever, the likely plastic chassis would relegate the model to mostly display..
The auction states the BODY is plastic. Pretty likely the chassis is metal.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 8:20 am
by Rufus T. Firefly
rex desilets wrote:I like it.
How good a model of the prototype is it then?
Howsomever, the likely plastic chassis would relegate the model to mostly display.
Maybe. Probably. Depends on use level?
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 11:00 am
by rex desilets
E7 wrote:rex desilets wrote:I like it. Howsomever, the likely plastic chassis would relegate the model to mostly display..
The auction states the BODY is plastic. Pretty likely the chassis is metal.
Don't think so. As I recall, the running versions of the Rivarossi locos used the same chassis as the static models.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 11:04 am
by Rufus T. Firefly
rex desilets wrote:E7 wrote:rex desilets wrote:I like it. Howsomever, the likely plastic chassis would relegate the model to mostly display..
The auction states the BODY is plastic. Pretty likely the chassis is metal.
Don't think so. As I recall, the running versions of the Rivarossi locos used the same chassis as the static models.
They did and LWS even sold a replacement brass chassis frame and drivers for the 0-8-0.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 11:05 am
by rex desilets
Rufus T. Firefly wrote:rex desilets wrote:I like it.
How good a model of the prototype is it then?
Hard to say from a couple of pix. Since there are decent plans for the RDG Mike, I'd be inclined to take a chance, especially since there are no (I suspect) models otherwise available.Howsomever, the likely plastic chassis would relegate the model to mostly display.
Maybe. Probably. Depends on use level?
Good point. I wonder if someone, say, Rufus, could reproduce the chassis in a hard resin.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 11:46 am
by Rufus T. Firefly
rex desilets wrote:Rufus T. Firefly wrote:Maybe. Probably. Depends on use level?
Good point. I wonder if someone, say, Rufus, could reproduce the chassis in a hard resin.
Ed Reutling made frames in resin; just need to inset bearings for the axles and should not be a problem. Metal filled resin is possible and doable.
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 12:16 pm
by Jay Criswell
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 12:35 pm
by Rufus T. Firefly
Nice!
Are you using the actual CJ plastic drivers to burn out and cast brass, Jay?
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 12:44 pm
by Jay Criswell
Martin,
Yes, direct burnout and cast after installing a plastic stud and filling in the original crank pin holes.
Jay
Re: Rivarossi Plastic Reading Mikado?
Posted: Tue Sep 17, 2019 1:22 pm
by Rufus T. Firefly
Jay Criswell wrote:Martin,
Yes, direct burnout and cast after installing a plastic stud and filling in the original crank pin holes.
Jay
Good use of them then!