aaaaarrrrrrrrrrrgggggggggghhhhhhhhhhhh!!!!!!!!!!
Posted: Fri Jul 31, 2020 5:30 pm
NOT model railroad related. Proper warning has been issued!
I have been dealing for weeks with a machinist. Known him for years, usually really good.
He's got a 48 Ford flathead V-8 in his shop for rebuild. I know more about these things than just about anyone left locally (KOOK- Keeper Of Obscure Knowledge).
48 and earlier had full floating rod bearings, 40PSI oil pump....I provided him with a 49-53 crank, full set of rods for use with Clevite bearings....and he's confused. I even drove out there this morning. He can't get the oil pump and screen to fit.
Has a 36-42 pump with integral screen, wore out. Replacement pumps are for 49-53, 60PSI. I took a 5 gallon bucket of pickups and screens, sorted that.....and the sump he's gonna use (oil pan) won't fit. Came off a donor motor he picked up, no idea why, had a transverse baffle. Old pan has no baffle, so cut the baffle out, right?
Why does one have a baffle and one doesn't? Do I really want to cut it out?
Got home, the calls and e-mails started in....aluminum rear main seal holders are not square cross section slot to accept a rope seal, rather narrow and tapered on one side.
Has a replacement crank, all done, one slinger (actually rear thrust), had him dig out the crank that was in his customer's engine when delivered. TWO slingers.
Okay, you have a 36-42 crank, NO rope seals, just a slinger.
How do we know that?
Take a tape measure, measure from a known spot on center main back to centerline of aluminum housing.
Why? Can't I just measure from rear main?
Oh, you can, in limited space, not well lit...
Then measure from the same spot on the crank and compare the two measurements.
What do you mean? Can't be precise with a tape measure!
It's good enough for this to see if that rear slinger lines up with the aluminum housings.
Then more e-mails, put the instructions in print, then he JUST called, still confused. had to re-explain someone, somewhere put a 36-42 crank, oil pump, screen and slinger housings into a 48 block.
Even sent him links to find the correct aluminum parts to actually hold the rope seals.
He may have it now. Waiting on another call.......
I think I'll go have a stroke
I have been dealing for weeks with a machinist. Known him for years, usually really good.
He's got a 48 Ford flathead V-8 in his shop for rebuild. I know more about these things than just about anyone left locally (KOOK- Keeper Of Obscure Knowledge).
48 and earlier had full floating rod bearings, 40PSI oil pump....I provided him with a 49-53 crank, full set of rods for use with Clevite bearings....and he's confused. I even drove out there this morning. He can't get the oil pump and screen to fit.
Has a 36-42 pump with integral screen, wore out. Replacement pumps are for 49-53, 60PSI. I took a 5 gallon bucket of pickups and screens, sorted that.....and the sump he's gonna use (oil pan) won't fit. Came off a donor motor he picked up, no idea why, had a transverse baffle. Old pan has no baffle, so cut the baffle out, right?
Why does one have a baffle and one doesn't? Do I really want to cut it out?
Got home, the calls and e-mails started in....aluminum rear main seal holders are not square cross section slot to accept a rope seal, rather narrow and tapered on one side.
Has a replacement crank, all done, one slinger (actually rear thrust), had him dig out the crank that was in his customer's engine when delivered. TWO slingers.
Okay, you have a 36-42 crank, NO rope seals, just a slinger.
How do we know that?
Take a tape measure, measure from a known spot on center main back to centerline of aluminum housing.
Why? Can't I just measure from rear main?
Oh, you can, in limited space, not well lit...
Then measure from the same spot on the crank and compare the two measurements.
What do you mean? Can't be precise with a tape measure!
It's good enough for this to see if that rear slinger lines up with the aluminum housings.
Then more e-mails, put the instructions in print, then he JUST called, still confused. had to re-explain someone, somewhere put a 36-42 crank, oil pump, screen and slinger housings into a 48 block.
Even sent him links to find the correct aluminum parts to actually hold the rope seals.
He may have it now. Waiting on another call.......
I think I'll go have a stroke
