For your evaluation
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: For your evaluation
This all seems really, really complicated. I build my own DC power packs using Variacs, step-downs, bridge rectifiers, and giant capacitors.
But the OP wants ripple-free DC, which sounds like a battery and a giant resistor. Or a really, really good filter. Oscilloscopes will show a ripple on almost anything that starts out with AC.
But the OP wants ripple-free DC, which sounds like a battery and a giant resistor. Or a really, really good filter. Oscilloscopes will show a ripple on almost anything that starts out with AC.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: For your evaluation
My Marn-0-Stats had a switch....big transformers and selenium disc rectumfriers one way, lead acid batteries the other.
You can't really fix a Tech III easily due to the SCR switching. On older units, like a 501, yes.
BEEP 68, ETA 69, Sub School and SINS school 70, fleet 71-74, with various ETC schools along the way.
I still have an EIMB, full volume, big as an old dictionary.
You can't really fix a Tech III easily due to the SCR switching. On older units, like a 501, yes.
BEEP 68, ETA 69, Sub School and SINS school 70, fleet 71-74, with various ETC schools along the way.
I still have an EIMB, full volume, big as an old dictionary.
Dave....gone by invitation
Re: For your evaluation
RDSRR wrote:What I don't understand is if this fancy card can handle DCC which is says......why would not the board have a DC to DC converter to take care of that issue... have a real hard time thinking all his customers are reinventing a power supply.
But Dan, it's so much more fun to do it this way.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
-
Tom Dempsey
- Posts: 1002
- Joined: Mon Dec 23, 2013 10:15 pm
Re: For your evaluation
RDSRR wrote:What I don't understand is if this fancy card can handle DCC which is says it can he has an AC/DC converter on board. Since most all power packs these days have pulse or whatever they call it, why would not the board have a DC to DC converter to take care of that issue... if it is a real issue. Just what exactly does this manufacture recommend people use with his product? If it's as popular as he says I have a real hard time thinking all his customers are reinventing a power supply.
Well Dan, that's why I always start a relationship by purchasing the product at retail, and trying it out. I don't sell what I don't use, or can't recommend, or can't support. That question has occurred to me also, but, I haven't quite got to asking him that. Of course, the dead rail option completely bypasses that issue, however, there are boucou MRC powerpacks out there and I don't really know what he's using for himself as of yet.
-
Tom Dempsey
- Posts: 1002
- Joined: Mon Dec 23, 2013 10:15 pm
Re: For your evaluation
bob turner wrote:This all seems really, really complicated. I build my own DC power packs using Variacs, step-downs, bridge rectifiers, and giant capacitors.
But the OP wants ripple-free DC, which sounds like a battery and a giant resistor. Or a really, really good filter. Oscilloscopes will show a ripple on almost anything that starts out with AC.
The problem for me Bob is that while I studied that stuff in school in the mid 70's, by the time I was actively working with electronics the first card in the rack was a A to D converter and then everything was digital. I really have problems with non solid state electronics/anything that are pre-eighties as my experience factor just ain't there. Working on the EMD stuff later on was pretty much follow the circuit and find where the power stopped.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: For your evaluation
Tom Dempsey wrote:bob turner wrote:This all seems really, really complicated. I build my own DC power packs using Variacs, step-downs, bridge rectifiers, and giant capacitors.
But the OP wants ripple-free DC, which sounds like a battery and a giant resistor. Or a really, really good filter. Oscilloscopes will show a ripple on almost anything that starts out with AC.
The problem for me Bob is that while I studied that stuff in school in the mid 70's, by the time I was actively working with electronics the first card in the rack was a A to D converter and then everything was digital. I really have problems with non solid state electronics/anything that are pre-eighties as my experience factor just ain't there. Working on the EMD stuff later on was pretty much follow the circuit and find where the power stopped.
Yeah. I hit that weird spot...trained on vacuum tubes (valves), then transitioned into transistors....never did much into chips. Navy used a lot of older design stuff..some to be more EMP resistant, methinks.
SINS..old style with a binnacle, gyros, PIPAs, early computers, servos....SPS-6 radar was vacuum tube...but I've done radio/battery for 25 years out doors, even made a good living at it.
Battery is the best source for pure, unadulterated DC..big charger to keep it up. But if you want grunt, a 15A Bridgeworks will, in fact, do the job, and leave you some headroom. Most have a slider stop, but be advised, with little load they can peak high on voltage, and fry an older sound card with no motors across the load.
I've had lots of old MRC's open, no caps, usually the bridge rectumfrier is blown (one I have a guy used to run his 0 2 rail Big Boy continuously..501? H0 pack....gave it to me, bigger bridge, hasn't failed me in 25 years now.
Stay away from the units with a wiper across the secondaries. They will fail if you use them up and down, up and down, for a long time. If you are building an old transistorized tethered throttle (lite a TAT IV?) just crank them all the way up and tape across the knob.
Dave....gone by invitation
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: For your evaluation
Tom: I am no great shakes at either analog or digital, but if you want a good power pack with reasonably ripple free output, make the following mod to your diagram:
On the input, put a small circuit breaker, and then a small variac. Feed your stepdown with the variac output.
Just past the bridge rectifier, get rid of the transistors, and install a capacitor the size of a frozen orange juice can across the output. Then go through your ammeter, connect your voltmeter across the output, wire in the DPDT switch, install a 5 amp breaker, and you are done - a pretty package, a "power on" red light, and banana plug outlets for both AC and DC are really nice but not essential.
Not as pure as a battery, but not bad.
On the input, put a small circuit breaker, and then a small variac. Feed your stepdown with the variac output.
Just past the bridge rectifier, get rid of the transistors, and install a capacitor the size of a frozen orange juice can across the output. Then go through your ammeter, connect your voltmeter across the output, wire in the DPDT switch, install a 5 amp breaker, and you are done - a pretty package, a "power on" red light, and banana plug outlets for both AC and DC are really nice but not essential.
Not as pure as a battery, but not bad.
Re: For your evaluation
Tom Dempsey wrote:Every Power Pack I have seems to be a pulsed unit (most are MRC or starter set packs) and they are "messing" with the board I am currently trying to install in a locomotive. What I want is up to 6 amps of straight DC, no ripple, no pulse, a straight line on an oscilloscope at 12 volts. Your evaluation would be gratefully accepted, brutality is allowed/encouraged (if necessary). Thanks, as always, Tom Dempsey
Another approach is to fix the onboard electronics so that they'll work with standard power supplies. What is this board you're using?
Torturers, White Racists, Gay Bashers, Rich Psychopaths.
-
Seaboard Air Line Fan
- Posts: 1308
- Joined: Mon Mar 08, 2004 9:49 pm
- Location: Virginia
Re: For your evaluation
Here's my "transformer":
And my wiring diagram:
Also need a Transmitter:
The BIK-U3 is an On/Off switch with polyfuses and the charging jack, you'll also need a charger:
No wires to the layout, the entire track is a dead spot
No sound though, yet, and no smoke.
Good for 3 or 6 amps depending on what you buy.
I've been running for over 2 years now with ZERO failures, I get 2-1/2 hours of run time on a charge.
For those that already have a system this may be looked at as a waste of $$$, but starting from scratch it is definitely worth a look.
Here's where I get my Rx now:
http://rctrains.co.uk/
More on the RX65b:
http://rctrains.co.uk/Rx65b.htm
Took less than a week last order.
And my wiring diagram:
Also need a Transmitter:
The BIK-U3 is an On/Off switch with polyfuses and the charging jack, you'll also need a charger:
No wires to the layout, the entire track is a dead spot
No sound though, yet, and no smoke.
Good for 3 or 6 amps depending on what you buy.
I've been running for over 2 years now with ZERO failures, I get 2-1/2 hours of run time on a charge.
For those that already have a system this may be looked at as a waste of $$$, but starting from scratch it is definitely worth a look.
Here's where I get my Rx now:
http://rctrains.co.uk/
More on the RX65b:
http://rctrains.co.uk/Rx65b.htm
Took less than a week last order.
BobD aka Drifty
The Crow Flies At Midnight
The Crow Flies At Midnight
Re: For your evaluation
Bob, thank you for the schematic and parts URLs. I'm tentatively taking the step you have done. I have one R/C Battery powered loco with sound. I might go that route again, but the cost was pretty steep from that installer. Still I only have 3 more diesels to do and maybe one steamer.
Dan Weinhold
Dan Weinhold
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: For your evaluation
All of my R/C gear is RCS....going back 25 years. Pushbutton 27MC Elsema-based stuff, works just like it should. I wanted to use Walsham's new 2.4GC stuff, but cannot do a knob. Outdoors, rain and snow...we put the transmitters in ziplock baggies, can't operate knobs in baggies, so I used RCS America for later stuff.
Dave....gone by invitation
- Rufus T. Firefly
- Posts: 42243
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: For your evaluation
ScaleCraft wrote:snow...we put the transmitters in ziplock baggies, can't operate knobs in baggies...
Put the entire person in a baggie with the controller,
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: For your evaluation
Rufus T. Firefly wrote:ScaleCraft wrote:snow...we put the transmitters in ziplock baggies, can't operate knobs in baggies...
Put the entire person in a baggie with the controller,
Kewl. Now, since 90+ of the switches out doors are manual ground throws, and the couplers are all manual pin lifts....how do you do that when ensconced in a body bag(gie)?
Dave....gone by invitation
- Rufus T. Firefly
- Posts: 42243
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: For your evaluation
ScaleCraft wrote:Rufus T. Firefly wrote:ScaleCraft wrote:snow...we put the transmitters in ziplock baggies, can't operate knobs in baggies...
Put the entire person in a baggie with the controller,
Kewl. Now, since 90+ of the switches out doors are manual ground throws, and the couplers are all manual pin lifts....how do you do that when ensconced in a body bag(gie)?
Cut a slit in one side for 1 hand.....like a poncho.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: For your evaluation
Starting to rain.
Getting heavier (and note the TX Baggie)
Really coming down...and dark...note TX in Baggie at end of turntable.
Getting heavier (and note the TX Baggie)
Really coming down...and dark...note TX in Baggie at end of turntable.
Dave....gone by invitation
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 45 guests
