Model under construction IGN ( MP ) #896 Dome
Re: Model under construction IGN ( MP ) #896 Dome
more photo's
Re: Model under construction IGN ( MP ) #896 Dome
OK for those who are interested I am up loading the remainder of the finish build photo's. There are bout 10 major modules
that are screwed together to assemble all the components with 1.4 x 3 mm FH screws. probably a 100.
your saying holy batman why so many. Well it was the most logical method and to get all the detail and features
as shown in the photo's.
I might add that the roof was an all riveted Kemtron roof and all the rivets were removed to reflect the
Pullman style welded roof which was unique for this car.
Ok the finish yes is rough but will be grit blasted with 220 grit red oxide. cleaned with my Ultra sonic cleaner an
then the painting will begin.
thanks for all the interest.
Bill Basden
that are screwed together to assemble all the components with 1.4 x 3 mm FH screws. probably a 100.
your saying holy batman why so many. Well it was the most logical method and to get all the detail and features
as shown in the photo's.
I might add that the roof was an all riveted Kemtron roof and all the rivets were removed to reflect the
Pullman style welded roof which was unique for this car.
Ok the finish yes is rough but will be grit blasted with 220 grit red oxide. cleaned with my Ultra sonic cleaner an
then the painting will begin.
thanks for all the interest.
Bill Basden
Last edited by cole7015 on Mon Aug 28, 2017 9:33 pm, edited 1 time in total.
Re: Model under construction IGN ( MP ) #896 Dome
last of the photo's
- Erik C Lindgren
- Posts: 1307
- Joined: Wed Apr 28, 2010 11:37 pm
- Contact:
Re: Model under construction IGN ( MP ) #896 Dome
ABSOLUTELY MAGNIFICENT!!!!!
- Erik C Lindgren
- Posts: 1307
- Joined: Wed Apr 28, 2010 11:37 pm
- Contact:
Re: Model under construction IGN ( MP ) #896 Dome
Would you be willing if I paid you to build me a dome for a 1938 PRB Budd Coach? My bucket list car is the pattern dome for CB&Q..
Re: Model under construction IGN ( MP ) #896 Dome
Another superb build and I am learning a lot in the process.
Regards,
Dan
The Model Railroad Resource LLC
407 East Chippewa St - Dwight, IL 60420
Voice 815.584.1577 / FAX 800.783.0127
daniel@modelrailroadresource.com / http://modelrailroadresource.com
http://oscaleresource.com/ and http://sscaleresource.com/
Dan
The Model Railroad Resource LLC
407 East Chippewa St - Dwight, IL 60420
Voice 815.584.1577 / FAX 800.783.0127
daniel@modelrailroadresource.com / http://modelrailroadresource.com
http://oscaleresource.com/ and http://sscaleresource.com/
Re: Model under construction IGN ( MP ) #896 Dome
Exquisite detail!
Dan Weinhold
Dan Weinhold
Re: Model under construction IGN ( MP ) #896 Dome
Bill,
Just wondering how you make your window cuts so uniform, particularly the radii at the corners. Any sheet metal I have ever cut, always had the tendency to curl.....how do you avoid that?
Thanks,
Rich
Just wondering how you make your window cuts so uniform, particularly the radii at the corners. Any sheet metal I have ever cut, always had the tendency to curl.....how do you avoid that?
Thanks,
Rich
Re: Model under construction IGN ( MP ) #896 Dome
Rich and Otheres.
thanks for your continued interest it is most appreciated be leave me.
Here is a very long winded answer to the question
Over the years windows have always been a bitch, especially when you have a lot. This car took about
4 days on the main car there are 23 windows sides 020". The dome took a week it sides are only .016" thick.
as you can see the side layout uses layout dye and the windows are scribbled with a scratch tool.
With the help oh a plastic car side from Union Station Products for a Pullman dome, I used as template.
Now the fun part. I use a HSS 1/8" dia drill and gang drill as close to the scribe line as I can get, next
I have several sizes of HSS burrs and clean uo the gang drill holes. Then there is hand filing a lot of it,
removing up to the scribe line when the layout dye is gone your close.
Final step the use of dial calipers measuring from a know edge to your window onece you have the
first window set for size the all fal into place.
Rounded corners I use a HSS 1/16" dia. Burr and being careful to remove material until it looks right
Have funn
Bill Basden
thanks for your continued interest it is most appreciated be leave me.
Here is a very long winded answer to the question
Over the years windows have always been a bitch, especially when you have a lot. This car took about
4 days on the main car there are 23 windows sides 020". The dome took a week it sides are only .016" thick.
as you can see the side layout uses layout dye and the windows are scribbled with a scratch tool.
With the help oh a plastic car side from Union Station Products for a Pullman dome, I used as template.
Now the fun part. I use a HSS 1/8" dia drill and gang drill as close to the scribe line as I can get, next
I have several sizes of HSS burrs and clean uo the gang drill holes. Then there is hand filing a lot of it,
removing up to the scribe line when the layout dye is gone your close.
Final step the use of dial calipers measuring from a know edge to your window onece you have the
first window set for size the all fal into place.
Rounded corners I use a HSS 1/16" dia. Burr and being careful to remove material until it looks right
Have funn
Bill Basden
E7 wrote:Bill,
Just wondering how you make your window cuts so uniform, particularly the radii at the corners. Any sheet metal I have ever cut, always had the tendency to curl.....how do you avoid that?
Thanks,
Rich
Re: Model under construction IGN ( MP ) #896 Dome
Bill, Sounds really painful!
Rich
Rich
Re: Model under construction IGN ( MP ) #896 Dome
Rich yes you are right. My right solder is very sore from repetitive motion.
If I had a longer milling bed, I would use that. But you will still have to file.
If I had a longer milling bed, I would use that. But you will still have to file.
E7 wrote:Bill, Sounds really painful!![]()
![]()
![]()
![]()
![]()
Rich
Re: Model under construction IGN ( MP ) #896 Dome
Final photo's showing module break down, prior to prep for painting. these will
now be grit blasted and cleaned for painting. Main paint products is Scale Cote 1
baked at 175 deg for 2 hours. results in the most durable finish you have ever seen.
Body color is my mix of Missouri Pacific Eagle blue and Eagle gray., using Floquil
baked as well over the base color..
Regards
Bill Basden Delta Models http://www.deltamodelsusa.com
now be grit blasted and cleaned for painting. Main paint products is Scale Cote 1
baked at 175 deg for 2 hours. results in the most durable finish you have ever seen.
Body color is my mix of Missouri Pacific Eagle blue and Eagle gray., using Floquil
baked as well over the base color..
Regards
Bill Basden Delta Models http://www.deltamodelsusa.com
Last edited by cole7015 on Wed Aug 30, 2017 8:57 am, edited 2 times in total.
- Rufus T. Firefly
- Posts: 42240
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Model under construction IGN ( MP ) #896 Dome
cole7015 wrote:....... remove material until it looks right
Not unlike sculpture,
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Model under construction IGN ( MP ) #896 Dome
E7 wrote:Bill, Sounds really painful!![]()
![]()
![]()
![]()
![]()
Rich
Sounds amazing and proves there is no substitute, at our level, (no CNC machines) for hard work, dedication and skill. The windows came out looking like they are factory cut. Nice Job! You have a very supportive peanut gallery rooting for you.
BH
Re: Model under construction IGN ( MP ) #896 Dome
Bill, this dome car is so sooooo good.
Since you're a dealer; anyway you pick up decals in your catalogue?
Curious, as in part of your line; in a complimentary way.
I am sooo sick of trolling E Bay for good letterboards, and don't have an ALPS printer.
I say this as decals pretty much dictate what I do project wise.
Pete
Since you're a dealer; anyway you pick up decals in your catalogue?
Curious, as in part of your line; in a complimentary way.
I am sooo sick of trolling E Bay for good letterboards, and don't have an ALPS printer.
I say this as decals pretty much dictate what I do project wise.
Pete
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: Wburg Pete and 92 guests
