.

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

.

Postby 2railjon » Tue Jan 30, 2018 4:27 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:45 pm, edited 1 time in total.
Running that red block Charlie.

rrjjf
Posts: 593
Joined: Tue May 08, 2007 5:13 am
Location: Glen Arm Maryland

Re: Old Rivets & The FOM

Postby rrjjf » Tue Jan 30, 2018 7:05 pm

2RailJon,

When these Sunset 3rd Rail GG-1 models first arrived I was asked by several modelers who purchased them to go over them. I found that the frames were bent and keeping the drivers off of the rails. I managed to straighten the frames by putting a wooden pencil between the car body and the frame at an appropriate location and gently bending the frame using the pencil as a fulcrum. This was a quick fix and improved the operation of these models.

I do not have a high opinion of these locomotives. Look at your frame closely. This may be the problem with your loco.

Joe
Joe Foehrkolb

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Old Rivets & The FOM

Postby 2railjon » Tue Jan 30, 2018 8:27 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:45 pm, edited 1 time in total.
Running that red block Charlie.

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: Old Rivets & The FOM

Postby bob turner » Tue Jan 30, 2018 9:36 pm

I do have a high opinion, but think they need all six axles powered. Ditto the FF2.

rrjjf
Posts: 593
Joined: Tue May 08, 2007 5:13 am
Location: Glen Arm Maryland

Re: Old Rivets & The FOM

Postby rrjjf » Wed Jan 31, 2018 7:43 am

2RailJon.

I also remember shortening the length of the springs under the pilot truck mounting screws. The pilot trucks seemed to be lifting the drivers off of the track.

I never had to disassemble these models. I just slid the pencil between the car body bottom and the frame that holds the drive assembly.

Bob T. IMO These are very nicely done car bodies with lousy drives using cheap motors and all wheels should have been powered.

Joe
Joe Foehrkolb

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Old Rivets & The FOM

Postby 2railjon » Wed Jan 31, 2018 5:39 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: Old Rivets & The FOM

Postby sarge » Wed Jan 31, 2018 6:49 pm

See if that unpowered main axle isn't oversupporting as well; bloody stupid design having the pilot trucks and an unpowered wheel on opposite ends oversupporting the two driven ones. You'll have to treat each assembly as you would sorting a poorly sprung 4-4-2 steam loco.

Also, the weight is conveniently where it does the least good, over two undriven axles. Can you get some sheet lead under the motors and over the driven axles?

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: Old Rivets & The FOM

Postby bob turner » Wed Jan 31, 2018 6:59 pm

Sprockets and Delrin chain.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Old Rivets & The FOM

Postby 2railjon » Wed Jan 31, 2018 7:22 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
robert.
Posts: 6010
Joined: Mon Mar 02, 2015 9:24 am

Re: Old Rivets & The FOM

Postby robert. » Wed Jan 31, 2018 8:14 pm

Can you fill the shell with shot and epoxy
F30F3BC2-4991-47BA-9F3D-C83F183F1A5C.jpeg
I spend entirely too many hours a day tying my shoes

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Old Rivets & The FOM

Postby 2railjon » Wed Jan 31, 2018 9:15 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:46 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: Old Rivets & The FOM

Postby sarge » Thu Feb 01, 2018 7:17 am

Jon, if you've never done that stunt before, don't be tempted to use white glues or carpenters glue (PVA) with shot. I've seen many a model ripped apart as the mass swells pretty friskily over a long period of time.

User avatar
Rufus T. Firefly
Posts: 42220
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Old Rivets & The FOM

Postby Rufus T. Firefly » Thu Feb 01, 2018 8:45 am

Can you fill the shell with shot and epoxy


sarge wrote:Jon, if you've never done that stunt before, don't be tempted to use white glues or carpenters glue (PVA) with shot. I've seen many a model ripped apart as the mass swells pretty friskily over a long period of time.


If wanted, I could send you an ingot of Cerrobend to reshape to where it might fit. I might also find it possible to scrounge up some sheet lead.

Let me know, Jon
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Old Rivets & The FOM

Postby 2railjon » Thu Feb 01, 2018 9:15 am

.
Last edited by 2railjon on Sun May 27, 2018 5:47 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
rex desilets
Posts: 1786
Joined: Sun Jul 15, 2007 2:18 pm

Re: Old Rivets & The FOM

Postby rex desilets » Thu Feb 01, 2018 12:12 pm

Rufus T. Firefly wrote:<snip> I might also find it possible to scrounge up some sheet lead.
<snip>
Amazon.com
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” – John Adams


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: Google [Bot] and 46 guests