Is this ugly or What?
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
I had a couple models with Walsall drivers - shell cast cast iron. Very lacy in appearance. Not my favorite look. Lorenzen had a line of coined brass drivers that were quite good (until he plated the axles and pins; then they required careful re-machihing). All Nation look ok, and while you cannot just call BTS, they are still out there.
Joe is a source. I do have cast iron blanks, and have been known to send a set to joe for machining for a third party. So it is still possible to scratchbuild without Sarge's admonishment.
Joe is a source. I do have cast iron blanks, and have been known to send a set to joe for machining for a third party. So it is still possible to scratchbuild without Sarge's admonishment.
Re: Is this ugly or What?
Admonishment? Hardly.
Suggestion, yes. You mentioned trying to source drivers and doing these as articles. I was giving you an easy source that you can pass along in that article.
If you are doing them just for you, that's one thing. If you are doing these to present as article subjects for others to emulate, a ready source for all the parts becomes important.
Do as you will.
Suggestion, yes. You mentioned trying to source drivers and doing these as articles. I was giving you an easy source that you can pass along in that article.
If you are doing them just for you, that's one thing. If you are doing these to present as article subjects for others to emulate, a ready source for all the parts becomes important.
Do as you will.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
Back when I was regularly doing this sort of thing, I would suggest several alternatives. The UK drivers were a possibility, so I ordered a set. I got stung rather badly on a small shipment, but I personally did not care for the product. They were beautifully done, and spot-on for British steam.
Ed and I were friends for a while, and I actually reviewed one of his products in OSN. I had to bite my tongue, but I never said anything inaccurate about the model. About a decade later he decided he hated my guts. I never found out why. He was the reason for the "opinion" that follows most of my posts. It may have been my opinion about using different ratio gearboxes in articulated models. He did not like that idea.
Ed and I were friends for a while, and I actually reviewed one of his products in OSN. I had to bite my tongue, but I never said anything inaccurate about the model. About a decade later he decided he hated my guts. I never found out why. He was the reason for the "opinion" that follows most of my posts. It may have been my opinion about using different ratio gearboxes in articulated models. He did not like that idea.
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: Is this ugly or What?
rrjjf wrote:Bob Turner,
I would ream out the drovers and insert 1/4 drill rod axles.
Joe
I would be very careful about reaming out those drovers!
Re: Is this ugly or What?
J.S. Bach,
I have performed this operation several times to save All Nation drivers that have worn down "D" openings due to the drivers being operated with loose axle nuts. I ream the drivers to 0.249" with a precision reamer and install the drivers on the new 1/4" axles with some Loctite 609 Retaining Compound...no more loose drivers. I can quarter drivers accurately without the need for the "D slots and All Nation axles.
Varney designed their drivers to be assembled by a modeler that did not have the tools or skills necessary to accurately quarter drivers. Their method works until the drivers start to work loose while in operation and the Zamac driver center becomes worn and this results in a loose fit.
When assembling a new set of drivers I will use them as designed but add a drop of Loctite 242 (removeable) to the threads on the ends of the Varney axles before tightening them down. This seems to work.
What is your concern?
Joe
I have performed this operation several times to save All Nation drivers that have worn down "D" openings due to the drivers being operated with loose axle nuts. I ream the drivers to 0.249" with a precision reamer and install the drivers on the new 1/4" axles with some Loctite 609 Retaining Compound...no more loose drivers. I can quarter drivers accurately without the need for the "D slots and All Nation axles.
Varney designed their drivers to be assembled by a modeler that did not have the tools or skills necessary to accurately quarter drivers. Their method works until the drivers start to work loose while in operation and the Zamac driver center becomes worn and this results in a loose fit.
When assembling a new set of drivers I will use them as designed but add a drop of Loctite 242 (removeable) to the threads on the ends of the Varney axles before tightening them down. This seems to work.
What is your concern?
Joe
Joe Foehrkolb
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
I agree - turns out most of my AN drivers have the "flat" torn out. Makes little difference on a two axle unsprung locomotive; I will quarter by eyeball and Loctite. Joe's method is good, but you need a lathe with a really good concentric mount to do the ream job. A step-collet comes to mind.
I don't use AN drivers very often. Except for this and the Varney ten-wheeler, they are too lacy for me. All my Mountains, the Pacific, and Atlantic, got cast iron.
I don't use AN drivers very often. Except for this and the Varney ten-wheeler, they are too lacy for me. All my Mountains, the Pacific, and Atlantic, got cast iron.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
Here is the project as it stands. I did most of it a decade ago, then last night prepared the firebox and window sheets. We'll see . . . It does belong in the ugly thread for now.
I did paint and add class lamps to the ugly American. Forgot to include it in my photo shoot. No longer quite so ugly.
I did paint and add class lamps to the ugly American. Forgot to include it in my photo shoot. No longer quite so ugly.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
Here is another ugly - laying around for probably a quarter-century. There is hope; those two Berks were laying around for longer than that!
Front truck is off the track for Dave. I didn't even know it had a front truck.
Front truck is off the track for Dave. I didn't even know it had a front truck.
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: Is this ugly or What?
rrjjf wrote:J.S. Bach, What is your concern? Joe
You made a humorous typo, "drovers" for "drivers". I just thought that it was funny as "drovers" refers, usually, to those folks who handle cattle.
Re: Is this ugly or What?
J.S.,
Missed that. Never try to ream out a drover! As I get older my typing gets sloppier.
Joe
Missed that. Never try to ream out a drover! As I get older my typing gets sloppier.
Joe
Joe Foehrkolb
-
Tom Dempsey
- Posts: 1002
- Joined: Mon Dec 23, 2013 10:15 pm
Re: Is this ugly or What?
Let the cows end up in a ravine and watch a drover get reamed out big time buddy.
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: Is this ugly or What?
rrjjf wrote:J.S.,
Missed that. Never try to ream out a drover! As I get older my typing gets sloppier. Joe
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Is this ugly or What?
Here is the original ugly, with a little rattle can paint and some fingernail polish:
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Is this ugly or What?
Looking better & better,

What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Is this ugly or What?
Rufus T. Firefly wrote:Looking better & better,![]()
Agreed! The red accents are small, but they add major interest.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: sleepmac and 27 guests