So....I ended up with a box of Half Zero stuff a week ago.
Stripped and reassembled a badly painted and in pieces Silver Streak caboose....an Ulrich stock car (geez, never again), and a bunch of other things...and an ALCO demonstrator loco.
Maroon, with grey and yellow stripes...number 430.
Looks like an RSD-15. Checked it out, all six axles geared. What's this.....a center gearbox...pull the shell...open frame motor driving box, driveshafts to each truck UNDER the frame.
"GILBERT". And it's an RSD-7, of which TWO prototypes were built. DL-600, to be precise, whereas an RSD-15 is a DL-600B
Very similar locomotives except for 244 and 251 prime movers.
Runs good. Never seen one before.
Back to your regularly scheduled thread drift.
ALCO diseasemal.....NOT 0
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
ALCO diseasemal.....NOT 0
Dave....gone by invitation
Re: ALCO diseasemal.....NOT 0
The DL600s are personal favourites of mine. I knew them "up close and personal" in DeWitt. There was a DL600a there that sat at the dieselhouse and I never saw it run. We had two DL600b, the RSD15s. They were ex-PRR, our 6813 and 6815. They were heavy switchers and hump engines in Syracuse, originally set up as helper power from new for PRR. Hugely capable things, you could pull full train-length cuts of cars with one, and put it over the hump to classify into new trains all in one go.
The next yard east was Selkirk, and they also had a pair. When they got some new U23c for heavy switchers, DeWitt got one of their RSD15s; 6814. I want to say the other went to Providence, but 6814 came in non-running condition having sat for a while after the GEs came to Selkirk. It went through the shop, and came out all pretty and fresh to join the other two.
They were monsters, and I have fond memories of them.
Atlas did a generic one as part of their Trainman series in O. I have one here that I've pretty well broken every bone in its body to detail as one of our trio. The PRR RSD15s only had a single tank underneath (though the RSD7s had a water tank in that space; they were built as passenger helpers complete with steam generators). Along with that was stripping the venting off the short hood and a bunch of little things like moving the horns.
New decals are coming from Microscale, so now a choice of which of the trio this ends up being. I could leave it, but 6814 lost the by then very tired red-P scheme when it came to DeWitt. So, we'll see what happens...
The next yard east was Selkirk, and they also had a pair. When they got some new U23c for heavy switchers, DeWitt got one of their RSD15s; 6814. I want to say the other went to Providence, but 6814 came in non-running condition having sat for a while after the GEs came to Selkirk. It went through the shop, and came out all pretty and fresh to join the other two.
They were monsters, and I have fond memories of them.
Atlas did a generic one as part of their Trainman series in O. I have one here that I've pretty well broken every bone in its body to detail as one of our trio. The PRR RSD15s only had a single tank underneath (though the RSD7s had a water tank in that space; they were built as passenger helpers complete with steam generators). Along with that was stripping the venting off the short hood and a bunch of little things like moving the horns.
New decals are coming from Microscale, so now a choice of which of the trio this ends up being. I could leave it, but 6814 lost the by then very tired red-P scheme when it came to DeWitt. So, we'll see what happens...
Re: ALCO diseasemal.....NOT 0
Can't make out the detail on the ends, but from what I can see, they are similar to an RS-11, which is a decent looking loco.
Nice model, Sarge.
Nice model, Sarge.
Re: ALCO diseasemal.....NOT 0
They are contemporaries of the RS11/RS36/RS32/RSD12, but much longer. That length is split between long and short hood pretty proportionally.
Here is one of them, a slide shot of mine from maybe 1974 or so:
In the low hood version, these were what was known as the "Alligator" on Santa Fe.
These were also the direct anticedent to the big Centuries, starting with C628.
Interesting the earlier version, the RSD7, had the 16 cylinder 244 (from the PA2/3), 2250hp. The RSD15 is pretty much visually identical, but with a 16 cylinder 251 at 2400hp. The RS11 and family had 12 cylinder versions of the 251, so they could be quite a bit shorter.
How much do you not want to sit next to the guy that is just bursting to tell you that in a social setting? Grin!
Here is one of them, a slide shot of mine from maybe 1974 or so:
In the low hood version, these were what was known as the "Alligator" on Santa Fe.
These were also the direct anticedent to the big Centuries, starting with C628.
Interesting the earlier version, the RSD7, had the 16 cylinder 244 (from the PA2/3), 2250hp. The RSD15 is pretty much visually identical, but with a 16 cylinder 251 at 2400hp. The RS11 and family had 12 cylinder versions of the 251, so they could be quite a bit shorter.
How much do you not want to sit next to the guy that is just bursting to tell you that in a social setting? Grin!
Re: ALCO diseasemal.....NOT 0
Well Sarge, I rather enjoy such mongrel diesels. I especially enjoy your ramblings about them from past encounters. Never hesitate to burst into all out info frenzies when the mood moves you...
Robert
Robert
Re: ALCO diseasemal.....NOT 0
sarge wrote:Interesting the earlier version, the RSD7, had the 16 cylinder 244 (from the PA2/3), 2250hp. The RSD15 is pretty much visually identical, but with a 16 cylinder 251 at 2400hp. The RS11 and family had 12 cylinder versions of the 251, so they could be quite a bit shorter.
How much do you not want to sit next to the guy that is just bursting to tell you that in a social setting? Grin!
Puts me in mind of an "olde" column, "Exit Laughing" in "Field and Stream" by Ned Zern about a "gun nut" friend who only spoke in terms of calibers, ballistics and powder loads! I think what we're discussing is called an enthusiast!
Rich
Re: ALCO diseasemal.....NOT 0
Cool Alco Sarge. I like the later high nose RS series Alco's a lot. Specifcally the NH and ex NYC and PRR "PC-ized" versions; there's a good photo of RSD-15 #6816 in service at Camden on page 101 of MS PC in color Vol 2 by Plant, shows the roof details nicely.
I missed getting your Trainman version, I've have the Weaver RS-11 and RSD-12 and I was fighting my "collect them all" urge as impractical.
Conversely I see what these look like and it seems like its impractical to fight the "collect them all" urge.
I have yet to remove and replace all the cast on detail like grabs in the Weaver's so it's probably just as well.
One beef I have with both these Atlas and Weaver RS's are the EMD-like side hand rail posts extending down the chassis sides, and have been considering what options there are for fixing that issue.
I missed getting your Trainman version, I've have the Weaver RS-11 and RSD-12 and I was fighting my "collect them all" urge as impractical.
Conversely I see what these look like and it seems like its impractical to fight the "collect them all" urge.
I have yet to remove and replace all the cast on detail like grabs in the Weaver's so it's probably just as well.
One beef I have with both these Atlas and Weaver RS's are the EMD-like side hand rail posts extending down the chassis sides, and have been considering what options there are for fixing that issue.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
Re: ALCO diseasemal.....NOT 0
De Bruin wrote:Cool Alco Sarge. I like the later high nose RS series Alco's a lot. Specifcally the NH and ex NYC and PRR "PC-ized" versions; there's a good photo of RSD-15 #6816 in service at Camden on page 101 of MS PC in color Vol 2 by Plant, shows the roof details nicely.
I missed getting your Trainman version, I've have the Weaver RS-11 and RSD-12 and I was fighting my "collect them all" urge as impractical.
Conversely I see what these look like and it seems like its impractical to fight the "collect them all" urge.
I have yet to remove and replace all the cast on detail like grabs in the Weaver's so it's probably just as well.
One beef I have with both these Atlas and Weaver RS's are the EMD-like side hand rail posts extending down the chassis sides, and have been considering what options there are for fixing that issue.
This is a real memory test, but I believe 6816 might have been the second Selkirk unit, so might have gone to Camden when 6814 came to us.
Regarding railings, its one of my pet peeves and one I can now pretty much let loose with, now that I'm just another modeller. We seem to have been stuck with things like China Drives and fold-up stanchions on hermaphrodite locos because the hirail world believed that sort of thing superior since Lionel did locos that way, at least that was the story we were told.
I was always rather disappointed at the excuse, and how O Scale fidelity had to be rolled backwards in time to accomidate, especially when an importer would not have remotely considered taking such liberties in fidelity, performance, and compatibility with anything they imported in HO or N. That mentality really put us back in time, if I'm honest, and the damage will never be undone in my lifetime. Once a model (especially a diesel) is done commercially, the chances of it being done again get really remote. Its really too bad so many really interesting prototypes are off the top of the playlist for this reason. I guess that's what happens when marketing becomes more important than modelling.
Its water under the bridge, but in the back of my mind is the idea of ordering up a couple sets of RS3 stanchions from Pat Mucci at P&D. There is absolutely no redeeming quality of the ones on my loco currently, which is a shame since the body is quite nice as are the the sideframes.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 40 guests
