Tank Cars

[R.K. Maroon]

That's an interesting coincidence -- I had never heard of these before somebody gave me one not long ago:

TankTrain.png (473.42 KiB) Viewed 6456 times

Those high pipes above the ends were used to load a string of these from just one end. Neat idea, but I'm guessing that means it would not be common to see just one by its lonesome self (dang). I was told this was a resin kit produced by Ed Reutling (Ruetling?). I have one of his Ingalls GM&O models, which is also resin, so it could be. Any idea, Jon?

Jim

[2railjon]

Jim, I’m not sure about your tank car. Mine is by Lionel. A string of 5 or 6 is my eventual goal, but I’ve only purchased this one so far to make sure it can be 2 railed with no issues.

[ScaleCraft]

That's an interesting coincidence -- I had never heard of these before somebody gave me one not long ago:

TankTrain.png

Those high pipes above the ends were used to load a string of these from just one end. Neat idea, but I'm guessing that means it would not be common to see just one by its lonesome self (dang). I was told this was a resin kit produced by Ed Reutling (Ruetling?). I have one of his Ingalls GM&O models, which is also resin, so it could be. Any idea, Jon?

Jim

Those high pipes are JATO nozzles. When there is a motive power shortage, they load the cars with JP-4, place car at end of train, wait for the green and hold up the Zippo.

[2railjon]

[robert.]

Would they need vacuum on the backend? Or do you think natural flow would push out the air ?

[ScaleCraft]

all sorts of information:

http://cs.trains.com/trn/f/111/t/173539.aspx

[Chris Webster]

Mine is by Lionel. A string of 5 or 6 is my eventual goal, but I’ve only purchased this one so far to make sure it can be 2 railed with no issues.

That will be a cool project.

Back in the mid-1980s, Conrail used to run a unit train of those cars from the Port of Albany, NY to Oswego, NY. The train ran over the former-NYC water level route from Albany to Solvay, where it switched onto Conrail's Baldwinsville Seconday to get to Oswego. I think I remember seeing it take the controlled siding in Utica and, another time, it came thru the fairgrounds entrance while we were at the State Fair.

Here's a picture of it that was posted to the EL mailing list: Picture taken from Williis Ave Bridge of TankTrain in Solvay, NY

[2railjon]

Dave & Chris, neat info!

[Carey Williams]

Hello O scale world
Here are a few tank cars to add to the train


left 1/4" ....top wood tank wrapped with paper, middle Scale Craft ..open to suggestions as to makers .right 17/64ths .... top to bottom Mi Loco (cast aluminum) , Mini -Scale (die-cast ) , and a mystery ...but nicely done .

Cheers Carey

IMG_9664.JPG (1.81 MiB) Viewed 6402 times

[bob turner]

Bottom left might be International.

I don't know what the bottom right is, but if brass with sand cast frame parts, I have three of them, and consider them among my most valued.

[2railjon]

Carey, Very nice collection!!

[ScaleCraft]

Middle left, on first glance, with truck sideframe retaining clips and oversized rivets along the top of the tank makes it SC
Top left may be a SC frame.

[ScaleCraft]

Trouble with top left is wood dowel tank, drawn on straps, homemade dome (or so one photo would indicate).
Still think SC frame, but Lionels are close.
I have one or two tanks here that are "messed with" and relegated to three rail.

[bob turner]

Speaking of Lionel . . .

Lionel 715.JPG (736.89 KiB) Viewed 6375 times

[bob turner]

Off-topic, but related: the only plastic model I really think highly of - both from Becker, on 11th Street, back in the days when Peter Witt streetcars roamed out front. fifteen bucks each.

Lionel 714.JPG (884.1 KiB) Viewed 6375 times