Feebay "Turner" Special
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Yes, there is value there. But nowhere near $160. Junk has value, and this pile, unless the mechanisms are exceptional, is junk.
Remember when we were kids - junk yards abounded. If you needed a flathead engine, you went to the junk yard. The word “junk”, like so many other words, is disfavored because it is associated with what it describes. So now it is “aesthetically challenged?”
Remember when we were kids - junk yards abounded. If you needed a flathead engine, you went to the junk yard. The word “junk”, like so many other words, is disfavored because it is associated with what it describes. So now it is “aesthetically challenged?”
- Rufus T. Firefly
- Posts: 42237
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Feebay "Turner" Special
Jay Criswell wrote:There is value in the items shown and I'm sure someone will make use of them. A piece here, a part there, after while you have enough to make something.
There are bidders that believe that they have more value than folks here at $167. I'm sure that the seller is relieved that this appears to be the case.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Up to $250, and still hours to go! Any bets? $350?
Re: Feebay "Turner" Special
They went for $315 and they were pretty poor renditions of the EMD nose. I don't know how many Adams variations are out there, but a couple of Bob's are way better renditions.
Here is one I think is a little better proportioned:
https://www.ebay.com/itm/Baldwin-Model- ... 0012.m1985
An F3, but essentially the same front.
Here is one I think is a little better proportioned:
https://www.ebay.com/itm/Baldwin-Model- ... 0012.m1985
An F3, but essentially the same front.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Not me - the Baldwin doorstops all miss the EMD roof curvature by a mile. And most later Adams E-7 and F-3 or FT castings were as good as they get. These are overpriced before the bidding starts. I would have invested in the E-7s at the $75 mark, including shipping.
Re: Feebay "Turner" Special
bob turner wrote:Not me - the Baldwin doorstops all miss the EMD roof curvature by a mile..
There was only one (at bottom left) that remotely resembled an E nose. Pull up the auction (link is below) and look at the headlights of the other two......way too long and way too large. They are "cartoonish". The shape of the cab of the Baldwin is light years better. (opinion)
https://www.ebay.com/itm/-/292655625215 ... 675.l10137
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Oh - you are correct. Those cannot be Adams castings. They are horrible any way you look at them, even the last one. Worse than the nice Baldwin E-7 I had.
Re: Feebay "Turner" Special
First thing i look at is the headlight, because that is most likely where they mess things up. If that is bad, they are usually pretty poor "copies"! I am guessing the MORE curves the MORE difficult it is to get something correct shape wise, and the EMD hood is probably the most difficult.
Re: Feebay "Turner" Special
Fresh from the ups box to the work bench. Pull off a few parts and eBay it.
https://www.ebay.com/itm/O-SCALE-BRASS- ... ey+jd.TRS1
https://www.ebay.com/itm/O-SCALE-BRASS- ... ey+jd.TRS1
I spend entirely too many hours a day tying my shoes
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
At least it is a better photo - you can kind of tell what it is. See the shallow roof curvature? That, and the "one piece" casting says "Baldwin". Surprised that Art found this group of value. Maybe Maroon has some insight?
Re: Feebay "Turner" Special
bob turner wrote:At least it is a better photo - you can kind of tell what it is. See the shallow roof curvature? That, and the "one piece" casting says "Baldwin". Surprised that Art found this group of value. Maybe Maroon has some insight?
The roof curve is the most minor of transgressions. Look at the headlight from the side....totally ridiculous....call it Jimmy Durante syndrome.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Headlights are easy to fix. Roof contours - not worth the effort. Nose contours are impossible to correct. Best to wait for an appropriately priced later Adams nose and roof.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Feebay "Turner" Special
Here is the Raymus E-7. I have since soldered it together and put underframe details in. I really like this one, but I shall also show you an Adams of the first quality:
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: Feebay "Turner" Special
That PRR one was my desktop photo for a long time.
Re: Feebay "Turner" Special
Difficult to compare the two fairly with only one painted, but (I think) the Adams just nudges out the Raymus. The pilot is off a tad on both. Start just below the headlight and draw a straight line down. The contour of the pilot should follow that line instead of protruding out like it does (opinion). If that were the case, and you notched out where the rear steps in the back of the pilot are locared (the square indents), it would be about as good as you could get for a casting. (again opinion)
Rich
Rich
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 47 guests