Feebay "Turner" Special

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Sat Jul 28, 2018 1:14 pm

Yes, there is value there. But nowhere near $160. Junk has value, and this pile, unless the mechanisms are exceptional, is junk.

Remember when we were kids - junk yards abounded. If you needed a flathead engine, you went to the junk yard. The word “junk”, like so many other words, is disfavored because it is associated with what it describes. So now it is “aesthetically challenged?”

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Feebay "Turner" Special

Postby Rufus T. Firefly » Sun Jul 29, 2018 10:31 am

Jay Criswell wrote:There is value in the items shown and I'm sure someone will make use of them. A piece here, a part there, after while you have enough to make something.


There are bidders that believe that they have more value than folks here at $167. I'm sure that the seller is relieved that this appears to be the case.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Wed Aug 01, 2018 1:37 am

Up to $250, and still hours to go! Any bets? $350?

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Feebay "Turner" Special

Postby E7 » Thu Aug 02, 2018 2:56 pm

They went for $315 and they were pretty poor renditions of the EMD nose. I don't know how many Adams variations are out there, but a couple of Bob's are way better renditions.

Here is one I think is a little better proportioned:

https://www.ebay.com/itm/Baldwin-Model- ... 0012.m1985

An F3, but essentially the same front.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Thu Aug 02, 2018 7:09 pm

Not me - the Baldwin doorstops all miss the EMD roof curvature by a mile. And most later Adams E-7 and F-3 or FT castings were as good as they get. These are overpriced before the bidding starts. I would have invested in the E-7s at the $75 mark, including shipping.

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Feebay "Turner" Special

Postby E7 » Fri Aug 03, 2018 2:27 pm

bob turner wrote:Not me - the Baldwin doorstops all miss the EMD roof curvature by a mile..


There was only one (at bottom left) that remotely resembled an E nose. Pull up the auction (link is below) and look at the headlights of the other two......way too long and way too large. They are "cartoonish". The shape of the cab of the Baldwin is light years better. (opinion)

https://www.ebay.com/itm/-/292655625215 ... 675.l10137

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Fri Aug 03, 2018 7:39 pm

Oh - you are correct. Those cannot be Adams castings. They are horrible any way you look at them, even the last one. Worse than the nice Baldwin E-7 I had.

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Feebay "Turner" Special

Postby E7 » Fri Aug 03, 2018 9:09 pm

First thing i look at is the headlight, because that is most likely where they mess things up. If that is bad, they are usually pretty poor "copies"! I am guessing the MORE curves the MORE difficult it is to get something correct shape wise, and the EMD hood is probably the most difficult.

User avatar
robert.
Posts: 6010
Joined: Mon Mar 02, 2015 9:24 am

Re: Feebay "Turner" Special

Postby robert. » Sun Aug 12, 2018 10:06 pm

Fresh from the ups box to the work bench. Pull off a few parts and eBay it.
https://www.ebay.com/itm/O-SCALE-BRASS- ... ey+jd.TRS1
I spend entirely too many hours a day tying my shoes

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Mon Aug 13, 2018 12:12 am

At least it is a better photo - you can kind of tell what it is. See the shallow roof curvature? That, and the "one piece" casting says "Baldwin". Surprised that Art found this group of value. Maybe Maroon has some insight?

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Feebay "Turner" Special

Postby E7 » Mon Aug 13, 2018 12:35 am

bob turner wrote:At least it is a better photo - you can kind of tell what it is. See the shallow roof curvature? That, and the "one piece" casting says "Baldwin". Surprised that Art found this group of value. Maybe Maroon has some insight?


The roof curve is the most minor of transgressions. Look at the headlight from the side....totally ridiculous....call it Jimmy Durante syndrome.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Mon Aug 13, 2018 12:54 pm

Headlights are easy to fix. Roof contours - not worth the effort. Nose contours are impossible to correct. Best to wait for an appropriately priced later Adams nose and roof.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Feebay "Turner" Special

Postby bob turner » Mon Aug 13, 2018 8:43 pm

Here is the Raymus E-7. I have since soldered it together and put underframe details in. I really like this one, but I shall also show you an Adams of the first quality:

Raymus E7 002.jpg
Raymus E7 002.jpg (1.19 MiB) Viewed 5640 times


PRR E-7.jpg
PRR E-7.jpg (60.34 KiB) Viewed 5640 times

J. S. Bach
Posts: 5820
Joined: Wed May 16, 2007 9:30 pm

Re: Feebay "Turner" Special

Postby J. S. Bach » Mon Aug 13, 2018 9:43 pm

That PRR one was my desktop photo for a long time.

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Feebay "Turner" Special

Postby E7 » Tue Aug 14, 2018 1:56 am

Difficult to compare the two fairly with only one painted, but (I think) the Adams just nudges out the Raymus. The pilot is off a tad on both. Start just below the headlight and draw a straight line down. The contour of the pilot should follow that line instead of protruding out like it does (opinion). If that were the case, and you notched out where the rear steps in the back of the pilot are locared (the square indents), it would be about as good as you could get for a casting. (again opinion)

Rich


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 51 guests