The Erie-Built
Re: The Erie-Built
Butch,
A collection of OSN was my first "purchase" and what helped me decide to go into "O" some 20 years back. Told me a lot of what was "out there" model wise. Never regretted that buy, and once OST came along, has about anything you wanted to know between the two!
Rich
A collection of OSN was my first "purchase" and what helped me decide to go into "O" some 20 years back. Told me a lot of what was "out there" model wise. Never regretted that buy, and once OST came along, has about anything you wanted to know between the two!
Rich
Re: The Erie-Built
bob turner wrote:Yes. .087". What do you expect out of me before noon? I am the guy who would start in Las Vegas at 1AM and land at JFK at sunup. Then I was done for.
We are birds of a feather in that respect, and sometimes I'm not too good PM!
Thanks again,
Rich
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
Once we get our photo posting going, I will do a clean version of this thread. Meantime I note that the nose now looks a lot better. If you check my photos, it looks like the left windshield is squinting. I mentioned " sneaking up" on it. I was a bit puzzled, because the height matched exactly on both windshields, and the "squinting" appeared more prominently in photographs.
Turned out the original plastic had a curvature on the left top that was not there on the right side! I guess you don't see it on the larger windshield Atlas chose to model.
I started writing for OSN when Dan Henon had his stroke. I figured his was the only mag that really suited my interests. I wrote some for OSR, as it seemed at the time to be sincerely wanting more 2-rail stuff. I suppose of all of it, my "How to Build an 0-6-0" series was the most effective. I know of several modelers who built models following that series.
Turned out the original plastic had a curvature on the left top that was not there on the right side! I guess you don't see it on the larger windshield Atlas chose to model.
I started writing for OSN when Dan Henon had his stroke. I figured his was the only mag that really suited my interests. I wrote some for OSR, as it seemed at the time to be sincerely wanting more 2-rail stuff. I suppose of all of it, my "How to Build an 0-6-0" series was the most effective. I know of several modelers who built models following that series.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
Just heard from the sand casting guy. He no longer does brass, so he farmed it out. The sides are done. The foundry says they look a lot better than expected. Remember, I am going for the "doorstop" look with this thing.
So as soon as they arrive, all pieces except fuel tank will be in hand. You may expect photos.
You can tell by the dates how long this has taken.
So as soon as they arrive, all pieces except fuel tank will be in hand. You may expect photos.
You can tell by the dates how long this has taken.
Re: The Erie-Built
Wow, progress better late than never. I look forward to seeing these. I have an early AA Atlas set in the NYC psgr lightening stipe scheme sans DCC boards and sound that I like a lot but want to find a another powered donor for a chassis to power the dummy.
Curious Bob, mayb have asked this before, did you trim down the windshields on the mold to render the "B-17" look or stick with Atlas' s later C-liner like windshields?
I would love a "B-17" A-B-A set to do in KCS.
Curious Bob, mayb have asked this before, did you trim down the windshields on the mold to render the "B-17" look or stick with Atlas' s later C-liner like windshields?
I would love a "B-17" A-B-A set to do in KCS.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
I added wax to the plastic. When Jay's buddy did the burnout, plastic and wax both burnt out.
We used the same trick for PA trucks many years ago - plastic and wax master, 5% too big. Burnout yielded one brass truck, to which I soldered brake hangars, bearing caps, etc. Then we used the brass to make a rubber mold.
This is semi-exciting. It is marginally possible that we could cast sides for Adams shells. I am going to make a pair of E-7A sides, and have them cast up. If satisfactory, we will allow interested modelers to order directly from the sand foundry.
This will be a semi-eleemosynary endeavor. If we do it.
We used the same trick for PA trucks many years ago - plastic and wax master, 5% too big. Burnout yielded one brass truck, to which I soldered brake hangars, bearing caps, etc. Then we used the brass to make a rubber mold.
This is semi-exciting. It is marginally possible that we could cast sides for Adams shells. I am going to make a pair of E-7A sides, and have them cast up. If satisfactory, we will allow interested modelers to order directly from the sand foundry.
This will be a semi-eleemosynary endeavor. If we do it.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: The Erie-Built
bob turner wrote:
This will be a semi-eleemosynary endeavor. If we do it.
and you can pass the alms to those of us who have naught.
Dave....gone by invitation
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
Sides came in this morning. They are the best sand castings I have ever seen. Photos soon.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
Tonight I got the sides and nose temporarily married. The roof needs some serious trimming - maybe tomorrow, then a photo.
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: The Erie-Built
bob turner wrote:Sides came in this morning. They are the best sand castings I have ever seen. Photos soon.
I could use them for masters then and cast in resin?
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
If you want the plastic masters, you are welcome to them. They are quite nice. Do the resin casts shrink?
The roof is becoming a problem - it has more arch than the nose. Fortunately, the real B-17 version has the same problem, with a snowplow-like transition. It will take a couple days and some more end-milling to sort this out.
The roof is becoming a problem - it has more arch than the nose. Fortunately, the real B-17 version has the same problem, with a snowplow-like transition. It will take a couple days and some more end-milling to sort this out.
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: The Erie-Built
bob turner wrote:If you want the plastic masters, you are welcome to them. They are quite nice. Do the resin casts shrink?
Generally very little if at all. Send them to me and next time I order RTV, I'll play with them - I have another large item to make a mold of in the queue now so after I clear the current resin casting efforts off my bench, I will be able to move forward with these. You should have my address. If not, there's one you can use on the OST web page.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Erie-Built
Okay. You need to know that I have zero interest in resin or plasic models, and I shall never have more than one "Erie-Built" on my roster. So any resin sides you may cast need not come here. The masters are yours.
On the other hand, a resin master for a bronze sand casting might be a labor saving proposition - a Williams E-7 shell could be a starting point. As of now, my plan is just a built-up master out of polystyrene. First will be B-unit aluminum sides.
On the other hand, a resin master for a bronze sand casting might be a labor saving proposition - a Williams E-7 shell could be a starting point. As of now, my plan is just a built-up master out of polystyrene. First will be B-unit aluminum sides.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 48 guests
