Machine Shop / Locomotive Drive Work

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Thu Nov 14, 2019 7:12 pm

Bob asked for more photos of the PAs on roster. I will provide one or two photos and a description of each unit, mostly to explain how I picked the two units that will be assigned to the Sunbeam and Lone Star. The numbering of the units is the order in which I purchased them. I will start with #1:

Image

This is an "all original" unit, one of the few that I have. It has the number board above the cab and the side marker lights, both of which are part of the casting and often ground off to match some prototype that didn't have them. The unit is missing some steps and a horn, but is otherwise in excellent condition. Note the cast front coupler hatch. This is the only one of these I have seen.

This unit has the original drive with a manual reverser:

Image

The presence of the front coupler hatch, the roofer number board, and the side markers leads me to want to finish this as an ATSF unit. Few railroads had them, and ATSF was one (I can ignore that they didn't have the hatch for long):

https://fineartamerica.com/featured/alco-pa-1-51-santa-fe-chief-diesel-locomotive-chicago-1946-wernher-krutein.html

If anybody know of photos of the hatch on other railroad's PAs, please let me know -- mostly just curious.

More later
Jim
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Machine Shop / Locomotive Drive Work

Postby ScaleCraft » Thu Nov 14, 2019 7:38 pm

Give me a clean shot of the ladder you need, maybe measurements. I have a bag o them for my Adams FT's, too many.
Dave....gone by invitation

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Machine Shop / Locomotive Drive Work

Postby bob turner » Thu Nov 14, 2019 8:27 pm

Thanks. I love these things. I had a coupler hatch around here someplace.
What are you planning for the stainless sides? I was thinking nickel plating, but that is no longer easy or inexpensive. Bumper shops used to do it for free.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Machine Shop / Locomotive Drive Work

Postby bob turner » Thu Nov 14, 2019 8:29 pm

Bob Smith had the original set silver plated. You probably don't want to do that - tarnishes quickly.

User avatar
rex desilets
Posts: 1786
Joined: Sun Jul 15, 2007 2:18 pm

Re: Machine Shop / Locomotive Drive Work

Postby rex desilets » Thu Nov 14, 2019 11:03 pm

Aren't there some finishes used by our model airplane brethren that would work?
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” – John Adams

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Thu Nov 14, 2019 11:31 pm

Bob, I would probably take the cheating way out on any warbonnet scheme and just paint the area that is supposed to be stainless steel. Last year I did a survey of the available silver, aluminum, stainless steel, and chrome paints that are readily available as part of building the Napolean hat trucks for my brother Pete's Sunbeam, and I was very pleased with the choices and the quality of finishes. Pete has tried those fancy natural metal paints and was not all that pleased at the results-vs-effort ratio (he may want to jump in here to comment).

On to the next unit: I have only one PB. Like my ATSF-designated unit #1, this one also came with the original drive (actually two):

Image

Additionally, this unit is the same vintage as unit #1, in that they both have the Central Locomotive Works mark on the underside of the roof:

Image

As it is, these are the only two units out of the six I have that have this mark. The shell assembly is clean on both units, so these are likely factory assembled shells (the modeler had to assemble the early ones). All in all, this unit seems well matched to unit #1, and it seems natural to have more than one unit if one is doing early ATSF, so my thought at present is to pair this B with the unit #1 A.

More later
Jim
The link below any photo will display the image full size

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Machine Shop / Locomotive Drive Work

Postby E7 » Fri Nov 15, 2019 2:35 am

R.K. Maroon wrote:Note the cast front coupler hatch. This is the only one of these I have seen.

If anybody know of photos of the hatch on other railroad's PAs, please let me know -- mostly just curious.

Jim


Never heard the term coupler "hatch" used, always coupler doors. Most were factory equipment. They were mandated on all diesel cab units of the PRR for a time.

Not a great shot but here is a guy opening them:

https://www.facebook.com/altoonaworks/p ... =3&theater

Rich

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Sun Nov 17, 2019 10:35 pm

Thanks for the link, Rich. I used hatch instead of doors, as I think of doors as something that would lay flush with the car body instead of the clearly protruding profile of the hardware found on the earliest PAs. I cannot speak as to the official name for this thing, which the ATSF shop crews mysteriously lost one day when the units came in for service (or so I imagine).

Ok, next up, unit #3:

Image

Image

This unit came with an original drive but is missing the front truck. It also appears to be a factory assembled unit (more on this later). My plan is to pair unit #3 with unit #5, shown below:

Image

Image

As can be seen, this one came as a dummy. I have an extra original drive for this one, which will conveniently free up an unpowered truck for unit #3. Both of these units have the original side markers, but only one has the roof number board. That makes the pair suitable for GM&O -- Of their two PAs, one had the roof number board and the other did not. The dynamic brakes would need to be removed though, so I may change my mind about these two. Plenty of projects in front of these two, so no hurry here.

To be continued
Jim
The link below any photo will display the image full size

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Machine Shop / Locomotive Drive Work

Postby bob turner » Mon Nov 18, 2019 1:10 am

Thanks! I was locked out for about 24 hours - happy to be back.

The only serious cutting I would do is to remove the widow's peak appearance of the windshields (be careful; doesn't take much). Then you could do an ABA ATSF.

I have as many as you, and I promise I would jump on another. It's a sickness.

I have made a roof out of wood with no detail. Works, while I wait for more fragments.

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Mon Nov 18, 2019 1:21 pm

Bob -- The attraction of an ATSF ABA set is undeniable, and that is something to consider. However, I tend to align my locomotive projects to whatever train I have on roster for the locomotive to pull. I have an ATSF streamliner, but it's only four cars long (eight if you add in a heavyweight baggage and three express reefers:

Image
Image

I do like this train, but it's not exactly the Super Chief, and certainly not in need of an ABA set of PAs.

On a side note, some of these PAs have an odd feature. The access hatch on the fuel tank skirt should be forward on both sides. As it is, some of the units have the hatch forward on one side and to the rear on the other:

Image
Image

It would be wonderful if I could swap them around and fix them all, but sadly all the units with this problem have the "hatch on the right" skirts. A survey of these units shows that what I believe are the older ones have the problem and the newer ones don't, which suggests that Bob Smith at CLW didn't notice this detail at first, shipped the early units with the same part for both sides, and later created a new part to correct the problem.

Jim
The link below any photo will display the image full size

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Machine Shop / Locomotive Drive Work

Postby E7 » Mon Nov 18, 2019 2:35 pm

Jim, Don't sweat it! If their memory is as bad as mine, they'll forget where the d*mn thing is by the time they get it spun around! :lol: :lol: :lol:

Rich

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Machine Shop / Locomotive Drive Work

Postby Rufus T. Firefly » Mon Nov 18, 2019 3:07 pm

R.K. Maroon wrote:It would be wonderful if I could swap them around and fix them all, but sadly all the units with this problem have the "hatch on the right" skirts. A survey of these units shows that what I believe are the older ones have the problem and the newer ones don't, which suggests that Bob Smith at CLW didn't notice this detail at first, shipped the early units with the same part for both sides, and later created a new part to correct the problem.


Is it an applied part or is that an integral part of the body casting?
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Mon Nov 18, 2019 3:14 pm

Separate part, soldered to the shell
The link below any photo will display the image full size

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Machine Shop / Locomotive Drive Work

Postby Rufus T. Firefly » Mon Nov 18, 2019 3:20 pm

R.K. Maroon wrote:Separate part, soldered to the shell


So.....can it be removed to make a replacement, correct version w/o damaging it? Use it as a master to cast from, cut that up to make a new master, and recast at will?
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Machine Shop / Locomotive Drive Work

Postby R.K. Maroon » Mon Nov 18, 2019 4:07 pm

I have considered Rich's approach on the premise that if most people would never notice it then it is not a major sin. I had not considered Martin's idea of casting new skirts, but it certainly could be done. Another option would be to locate additional skirts. I contacted Lou Houlemarde to see if he had any of the skirts from the later "wrapper" CLW PAs in his inventory. He did have a couple (and sold them to me) but also found a couple of original skirts in his miscellaneous parts box. I still may be one short but close enough for now. As an aside, there were a few other original PA parts in Lou's parts box, including an extra drive. I started drooling so he sold me the whole box. That raises the question of where the line is between a good collection of spares and a pile of never-to-be-used parts.

Jim
The link below any photo will display the image full size


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 48 guests