1941 City of Los Angeles
- big bad jim
- Posts: 446
- Joined: Wed Oct 06, 2010 1:38 pm
Re: 1941 City of Los Angeles
Bob, the trucks for the 1941 COLA train sets were quite different from the typical trucks found on a lot of lightweight cars. The sideframes had a distinct profile, and they utilized truck mounted brake cylinders, various snubbers, and derailment guides. That was just the 2 axle trucks. There were of course the 3 axle trucks for the articulated cars, which I think were chair cars. I don't know how different the COLA 3 axle trucks were from others, although I presume the bolster(s) would be different.
There's a brief section on the trucks in the Streamliners book, in the middle of the chapter on the 1941 train sets.
There's a brief section on the trucks in the Streamliners book, in the middle of the chapter on the 1941 train sets.
- big bad jim
- Posts: 446
- Joined: Wed Oct 06, 2010 1:38 pm
Re: 1941 City of Los Angeles
I attached a couple of photos, but they didn't post. So perhaps we are out of space at the moment. Take a look at the Streamliners book. Or I could send you an email, which will most likely go into your spam folder. I'm presuming that's what happened with the last one I sent you, regarding the Morning Sun books for sale at the Cleveland show.
Jim
Jim
- R.K. Maroon
- Posts: 3141
- Joined: Tue Feb 22, 2011 9:20 pm
Re: 1941 City of Los Angeles
Here are the photos from the Kratville book. First the four-wheel trucks for the 1941 COLA:


These are the six-wheel, which were used on an articulated sleeper on that train:

Jim and I have been discussing the creation of the four-wheel trucks in O-scale for several years. We would probably get the project off the ground if I actually started in on building the cars for the train, so I would say the ball is in my court.
Here are a set of the trucks in HO:

If they can do it so can we.
Jim


These are the six-wheel, which were used on an articulated sleeper on that train:

Jim and I have been discussing the creation of the four-wheel trucks in O-scale for several years. We would probably get the project off the ground if I actually started in on building the cars for the train, so I would say the ball is in my court.
Here are a set of the trucks in HO:

If they can do it so can we.
Jim
The link below any photo will display the image full size
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: 1941 City of Los Angeles
I thought I had you on quick dial. I always answer my e-mail. I will check.
The one I did was simpler. I can't post photos either, but I will give the page number - in a minute.
Oh - and it was eight PAs and six PBs. The last four orders were for AB sets.
The one I did was simpler. I can't post photos either, but I will give the page number - in a minute.
Oh - and it was eight PAs and six PBs. The last four orders were for AB sets.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: 1941 City of Los Angeles
More E2 info:
All four "B" units (SF-2, SF-3, LA-2, LA-3) went to the Union Pacific; they were used until 1953, when they were "rebuilt" into E8 locomotives. These rebuilds utilized little of the previous locomotives and were effectively trade-ins. The driving "A" unit of the SF set, SF-1, (the "Queen Mary") went to the Southern Pacific; it was likewise "rebuilt" into EMD E7 #6017. The "A" unit of the LA set, LA-1, went to the Chicago and North Western (#5003A) and was scrapped in 1953 after it was destroyed in a head-on collision near Rhinelander, Wisconsin.
No E2 survives today. However the pair of Winton Model 201A V12 diesel engines from SF-1 (the lead unit of the City of San Francisco set, nicknamed "Queen Mary") were rescued from scrap and eventually became part of the collection of artifacts at the California State Railroad Museum at Sacramento. One of the engines has now (September 2009) been transferred to the Illinois Railway Museum at Union, Illinois.
All four "B" units (SF-2, SF-3, LA-2, LA-3) went to the Union Pacific; they were used until 1953, when they were "rebuilt" into E8 locomotives. These rebuilds utilized little of the previous locomotives and were effectively trade-ins. The driving "A" unit of the SF set, SF-1, (the "Queen Mary") went to the Southern Pacific; it was likewise "rebuilt" into EMD E7 #6017. The "A" unit of the LA set, LA-1, went to the Chicago and North Western (#5003A) and was scrapped in 1953 after it was destroyed in a head-on collision near Rhinelander, Wisconsin.
No E2 survives today. However the pair of Winton Model 201A V12 diesel engines from SF-1 (the lead unit of the City of San Francisco set, nicknamed "Queen Mary") were rescued from scrap and eventually became part of the collection of artifacts at the California State Railroad Museum at Sacramento. One of the engines has now (September 2009) been transferred to the Illinois Railway Museum at Union, Illinois.
Dave....gone by invitation
Re: 1941 City of Los Angeles
Roger Lewis imported some nice CUDO trucks over the years. I still have some of his 6 wheel Wasatch trucks, sold the 4 wheel trucks and then bought some CUDO 4 wheel trucks from Bill Davis. Believe they came from the same mfg.
-
Chris Webster
- Posts: 957
- Joined: Mon May 25, 2015 8:25 pm
Re: 1941 City of Los Angeles
R.K. Maroon wrote:A rough and brief history of the equipment list for the COLA is as follows:
1936: M-10000
FWIW, two of the Overland M-10000 4-car sets recently sold on ebay - I was surprised by how low the winning bids were:
Ebay #154043379997, sold for $231.49, set was missing two trucks
and
Ebay #333678173558, sold for $385.50 by TrainZ, noticeable dent on top of observation car
Re: 1941 City of Los Angeles
Yeah, it really is a representation of "supply and demand" in action. These were never great or even good sellers as I remember. They represented a very brief moment in UP history and were also poor runners IIRC. But, at these prices it's a steal just for display. These trains brought us into the Streamliner age and have historical significance for many collectors.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: 1941 City of Los Angeles
Wow! Twelve pages! I do not remember if I posted any Armour Yellow locomotives here - if not, stand by! I will get my money's worth out of Shuttlesworth.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: 1941 City of Los Angeles
Yep. Almost all photos of semi-finished models have been obliterated by Photobucket. So let's put them back in - I am sure Maroon has the COLA Diesel photos ready to go - here is mine, without the Photobucket label, and with thanks to Shutterfly, who is hosting me for free.

This is actually one of my favorites - CLW all cast; my very first, and powered by a giant (and very slow) Pittman 6000-series motor. The sprockets in all these have failed, and I really need to get with Jay for some replacements.
The trucks under that K-Line were done by Dennis - I mailed him candle-wax forms, poured into open topped molds, and he sent these back in bronze. Dennis has done an incredible amount of work to preserve older O Scale in bronze and nickel-silver.
This is actually one of my favorites - CLW all cast; my very first, and powered by a giant (and very slow) Pittman 6000-series motor. The sprockets in all these have failed, and I really need to get with Jay for some replacements.
The trucks under that K-Line were done by Dennis - I mailed him candle-wax forms, poured into open topped molds, and he sent these back in bronze. Dennis has done an incredible amount of work to preserve older O Scale in bronze and nickel-silver.
- R.K. Maroon
- Posts: 3141
- Joined: Tue Feb 22, 2011 9:20 pm
Re: 1941 City of Los Angeles
My embarrassment on this project continues. This may be the oldest thread here still alive, and I am honestly not much closer to getting it done than I was when I first posted it some six years ago. Aack. Bob indicated sometime back that I need to update the links to the photos to move them from Photobucket to Dropbox. I will work on this bit by bit -- hard to make it a priority.
In the meantime, here are three UP baggage cars acquired from skilled modeler Bob Jarvis at the recent Denver show:



I believe all three of these are American Standard. I had my eye on these from the opening of the show, but was really hoping somebody else would buy one or more to remove the temptation. But all were still available at the end of the show, and Bob offered a buy-two-get-three deal, so now they are on the roster. I love head-end cars, so I may just darn well run all three at once. I am no where near finishing the 1941 COLA but I could put together a suitable generic UP passenger train with a small amount of effort. Stay tuned -- The new shop is almost complete, which means the layout will go up before too long and trains will run again.
Jim
In the meantime, here are three UP baggage cars acquired from skilled modeler Bob Jarvis at the recent Denver show:



I believe all three of these are American Standard. I had my eye on these from the opening of the show, but was really hoping somebody else would buy one or more to remove the temptation. But all were still available at the end of the show, and Bob offered a buy-two-get-three deal, so now they are on the roster. I love head-end cars, so I may just darn well run all three at once. I am no where near finishing the 1941 COLA but I could put together a suitable generic UP passenger train with a small amount of effort. Stay tuned -- The new shop is almost complete, which means the layout will go up before too long and trains will run again.
Jim
The link below any photo will display the image full size
Re: 1941 City of Los Angeles
Glad to see this thread resurrected as I forgot all about it and any thread with UP in it is a winner for me.
I hope to be adding some "after" photos for some Wasatch cars I picked up last January. I made a good buy on a 12 car set or I wouldn't have jumped on them, but the reason for the good price was the owner (deceased) tried to paint most cars himself and even the ones that look okay have over spray, orange peel and dirt embedded in the paint. So, they all need to be stripped and repainted and I knew from the beginning they would go to Dan Pantera and I would have a lot more invested in them by the end.
Fortunately, only a few had any signs of handling damage (minor) and the boxes were good, so I'm happy with my purchase. As stated, I knew when I bought them they were going to Dan to have him work his magic. He mentioned an August finish date, but I won't hold him to it, as I just feel fortunate Dan's still doing these cars. Gary Schrader has already shutoff taking on new projects and Dan says he's looking to retirement as well.
These will be keepers for me, as I've owned other Wasatch cars that had Dan's paint, detail work and interiors installed, which is truly icing on the cake for these models. Roger Lewis hit is out of the ballpark with these cars and when you consider they were built prior to CAD and hand assembled back in the early 90's it just adds to the joy of owning them. I never tire of looking at them.
I've attached some photos of a few cars before shipment to Dan and I'll add a few photos of some cars Dan completed for another client, but need to transfer them to shutterfly first.
The 9000 series dome observation was painted by someone other than the former owner, but it has paint damage and a few other issues. Dan might be able to salvage it, but haven't heard.




I hope to be adding some "after" photos for some Wasatch cars I picked up last January. I made a good buy on a 12 car set or I wouldn't have jumped on them, but the reason for the good price was the owner (deceased) tried to paint most cars himself and even the ones that look okay have over spray, orange peel and dirt embedded in the paint. So, they all need to be stripped and repainted and I knew from the beginning they would go to Dan Pantera and I would have a lot more invested in them by the end.
Fortunately, only a few had any signs of handling damage (minor) and the boxes were good, so I'm happy with my purchase. As stated, I knew when I bought them they were going to Dan to have him work his magic. He mentioned an August finish date, but I won't hold him to it, as I just feel fortunate Dan's still doing these cars. Gary Schrader has already shutoff taking on new projects and Dan says he's looking to retirement as well.
These will be keepers for me, as I've owned other Wasatch cars that had Dan's paint, detail work and interiors installed, which is truly icing on the cake for these models. Roger Lewis hit is out of the ballpark with these cars and when you consider they were built prior to CAD and hand assembled back in the early 90's it just adds to the joy of owning them. I never tire of looking at them.
I've attached some photos of a few cars before shipment to Dan and I'll add a few photos of some cars Dan completed for another client, but need to transfer them to shutterfly first.
The 9000 series dome observation was painted by someone other than the former owner, but it has paint damage and a few other issues. Dan might be able to salvage it, but haven't heard.
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: 1941 City of Los Angeles
Nice cars. I have the K-Line version of the dome-observation; that will have to be good enough for me.
Re: 1941 City of Los Angeles
Wow! Butch, these are great.
Help the rest of us (unwashed not familiar with Wasatch,) are these a "cleaner"/ more improved version of the old Kemtron kits?
I'm sure Dan will do them justice, though it's really tedious to clean up bad paint, I hope we can see his finished efforts.
I like 'em all, but in particular that that 4-4-2 with upper "peak-a-boo" windows is awesome!!
Help the rest of us (unwashed not familiar with Wasatch,) are these a "cleaner"/ more improved version of the old Kemtron kits?
I'm sure Dan will do them justice, though it's really tedious to clean up bad paint, I hope we can see his finished efforts.
I like 'em all, but in particular that that 4-4-2 with upper "peak-a-boo" windows is awesome!!
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
Re: 1941 City of Los Angeles
Hey Pete. I've owned the K-Line, Kemtron and the Russ Briggs updated version of the Kemtron UP cars in the past 30+ years and they are all very nice and in the case of the Kemtron kits, a good place to start to build an exceptional model. The K-Line cars were ground breaking at the time, I sold my set to C.O. Gibson ......of course I didn't know him from Adam at the time and he actually had someone else make the 1st call on his behalf, which I found odd. But, knowing of him like I do now, this was not unusual behavior.
But the Wasatch cars were a new design from the ground up and faithfully follow a prototype UP car. I assume Roger was affiliated with Key at the time and used the Key builder for his cars, but never asked and don't know. They were all imported unpainted and Roger, like OMI, used "custom painters" if someone asked for paint. He imported these cars in both HO and O, but I can't remember which came 1st, but believe it was O.
They were imported without interiors or glazing, but the detail was correct as it could be made and pretty unbelievable (especially the bottom under floor detailing) way beyond the Kemtron kits offer since the 60's. The cars had functioning "dutch" doors in the vestibules and used small magnets to hold them open and closed, plus functioning folding/drop down stairs. Everything about the cars was way ahead of anything that proceeded them and still stand up well to today's super models.
I'll add some more photos today or tomorrow.
But the Wasatch cars were a new design from the ground up and faithfully follow a prototype UP car. I assume Roger was affiliated with Key at the time and used the Key builder for his cars, but never asked and don't know. They were all imported unpainted and Roger, like OMI, used "custom painters" if someone asked for paint. He imported these cars in both HO and O, but I can't remember which came 1st, but believe it was O.
They were imported without interiors or glazing, but the detail was correct as it could be made and pretty unbelievable (especially the bottom under floor detailing) way beyond the Kemtron kits offer since the 60's. The cars had functioning "dutch" doors in the vestibules and used small magnets to hold them open and closed, plus functioning folding/drop down stairs. Everything about the cars was way ahead of anything that proceeded them and still stand up well to today's super models.
I'll add some more photos today or tomorrow.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: Bing [Bot] and 28 guests
