1/72 Coronado flying boat

Play nice and have fun... AS OF JULY 12 2025, THIS FORUM IS LOCKED.
User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: 1/72 Coronado flying boat

Postby Rufus T. Firefly » Mon Dec 28, 2020 12:28 pm

chuck wrote:Thanks. I had some of that but stopped using it when I ran across Tenax 7R (which turned out to be 100% methylene chloride).


Which unfortunately is not available in that form now......and I hope my stock lasts a while.

I have the Testors MSDS and the ingredients are Xylene, N Butyl Acetate, Ethyl Benzene, Toluene, Naptha, and Polystyrene.


Hilarious - panic over and ban methylene chloride yet Xylene, Ethyl Benzene, and Toluene are acceptable. N-Butyl acetate is interesting - used to use it to test ventilation system quality -- smells a lot like bananas

The "no tox" blue label is basically citrus oil and usually makes quite a mess. I have left many fingerprints in styrene while trying to use it. I almost never seems to set completely. I suspect that's because it is "oil" based.


:roll: :roll: :roll: :roll: :roll:

I'll have to see if I still have a bottle of the black stuff that hasn't dried up and run some tests on it. It would be nice to have something that is a little less aggressive than methylene chloride. Tamiya extra thin (green label) is 50/50 mixture of Acetone (methyl methyl keytone) and Butyl Acetate.


A little less aggressive than methylene chloride would be nice, yet something that actually worked cleanly would also be good. Acetone literally blows away....N-Butyl acetate boils at over 100 degrees C so it's not going away.

Hate to suggest MEK; terribly flammable, nasty smelling, and all sorts of respiratory tox, but it does work on lots of plastics.....and it's still available as far as I know.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: 1/72 Coronado flying boat

Postby chuck » Mon Dec 28, 2020 1:40 pm

Same Stuff from MicroMark and Weld-On 3 and 4 are all Methylene Chloride, same as Tenax.

I started cataloging plastic welding compounds and this is a summary from the various MSDS sheets. I have emailed Tamiya about their "orange" bottle cement that is the consistency of honey but I have no idea whats in it. I would guess the thickness is polystyrene resin but I have no information on the solvent. I have seen numerous postings on forums about how all of these are the same (obviously not) and various "recommendations" on "cheaper" substitutes.

Tamiya Extra Thin Cement (green label)

Butyl Acetate 50.0 %
Acetone 50.0 %

Tamiya Plastic Cement (orange label)

Waiting for response from Tamiya

Testors Tube Cement

Toluene and aprox 25% by weight polystyrene

Testors Liquid Cement (3502/3520) Bottle with brush orange label

Ethyl Acetate 40%
MEK. 40%
Propylene Glycol Methyl ether Acetate 20%

Testors Liquid Cement/Model Master (3507/3507AT/8872C) triangular dispenser, black label

Xylene 37%
N Butyl Acetate 15%
Polystyrene 15%
Ethyl Benzene 15%
Naptha 7%
Toluene 1%


Testors No Tox (blue label)

d-Limonene 85% (citrus oil)

Plastruct Plastic Weld

Methylene Chloride ~85%
MEK ~15%

Plastruct Bondene

Methylene Chloride ~60%
Methyl Acetate ~40%

Plastruct Weldene

Polystyrene Resin ~20%
Dipentene Turpene Hydrocarbon ~80%

Plast-I-Weld

90% Methylene Chloride
10% MEK

Weld-On 3 & 4 and MicroMark Same Stuff

100% Methylene Chloride
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: 1/72 Coronado flying boat

Postby Rufus T. Firefly » Mon Dec 28, 2020 2:06 pm

chuck wrote:I would guess the thickness is polystyrene resin


Dissolved polystyrene -- filler material really that fills in the gaps in the joints -- old trick was to put scrap styrene into some Tenax to make it a gap filling solvent glue/adhesive.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: 1/72 Coronado flying boat

Postby chuck » Mon Dec 28, 2020 2:16 pm

I've been using thin sheet styrene as a gap filler on hulls and fuselages, actually anywhere it will fit. Stuff is paper thin. Used SameStuff to glue in place (actually fitted the sheet styrene and then applied the solvent) and then cut away the excess with a sharp knife. I applied a little more to melt the seam and then smooth with a micro chisel. Cuts down on puttying.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

philo426
Posts: 749
Joined: Sun May 15, 2005 8:51 pm

Re: 1/72 Coronado flying boat

Postby philo426 » Tue Dec 29, 2020 12:44 am

Mounted up the wings with a brass tube through the fuselage.Set the dihederal with a couple of stain cans. Image
Last edited by philo426 on Tue Dec 29, 2020 11:19 am, edited 1 time in total.

up148
Posts: 4800
Joined: Sat Nov 01, 2008 11:52 am

Re: 1/72 Coronado flying boat

Postby up148 » Tue Dec 29, 2020 10:03 am

Very nice work! I look forward to seeing more "work in progress reports" and the finished product. You build some really nice models.

User avatar
healey36
Posts: 7026
Joined: Fri Sep 03, 2010 4:43 pm
Location: Westminster, MD

Re: 1/72 Coronado flying boat

Postby healey36 » Tue Dec 29, 2020 10:29 am

philo426 wrote:Set the federal with a couple of stain cans.


I think the term is "dihedral"...effing spell-check :lol:

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: 1/72 Coronado flying boat

Postby chuck » Tue Dec 29, 2020 10:43 am

Yes, auto-incorrect. Not as bad as speech to text in voice mail but very close!
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

philo426
Posts: 749
Joined: Sun May 15, 2005 8:51 pm

Re: 1/72 Coronado flying boat

Postby philo426 » Tue Dec 29, 2020 11:19 am

Sorry that auto correct is a nuisance.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: 1/72 Coronado flying boat

Postby chuck » Tue Dec 29, 2020 11:47 am

Sorry that auto correct is a nuisance.


It's not. It sometimes is hilarious. When I was working I would get at least one confused email response where autocorrect completely mangled something I typed. I often wondered if it could be adapted for encryption purposes? Between spell check and "grammar" check it could slice and dice a message into something completely different. Sure hope it isn't used on the "hot line" between governments. Good way to accidentally start a war.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: 1/72 Coronado flying boat

Postby Rufus T. Firefly » Tue Dec 29, 2020 2:11 pm

philo426 wrote:.........with a couple of stain cans.


They do make good tools, weights, and supports!
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

philo426
Posts: 749
Joined: Sun May 15, 2005 8:51 pm

Re: 1/72 Coronado flying boat

Postby philo426 » Tue Dec 29, 2020 2:24 pm

Yep!

philo426
Posts: 749
Joined: Sun May 15, 2005 8:51 pm

Re: 1/72 Coronado flying boat

Postby philo426 » Tue Dec 29, 2020 3:42 pm

Empennage installed. Image

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: 1/72 Coronado flying boat

Postby chuck » Tue Dec 29, 2020 4:38 pm

Wow! You are fast. Grey stuff primer or two part filler? I see a cup in the upper right corner near the baking soda.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

philo426
Posts: 749
Joined: Sun May 15, 2005 8:51 pm

Re: 1/72 Coronado flying boat

Postby philo426 » Tue Dec 29, 2020 4:54 pm

After I sand the putty off I like to check with dark gray paint.The cup is for cleaning the brush !


Return to “The Club Car Lounge”

Who is online

Users browsing this forum: No registered users and 64 guests