Bowed urethane castings - thoughts on a fix?

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Bowed urethane castings - thoughts on a fix?

Postby bob turner » Sun Feb 13, 2022 10:55 pm

What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Sun Feb 13, 2022 11:59 pm

bob turner wrote:What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?


Yes, when I was trying to straighten it earlier, it clamps down straight cold just fine. I suppose I could cut down a sacrificial piece of plywood to throw in the boil. Gotta see if I have a pot big enough to hold this thing even tho its maybe 35-40'.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 2:47 am

Current status (Pre-boil):

Image


Image
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Bowed urethane castings - thoughts on a fix?

Postby Rufus T. Firefly » Mon Feb 14, 2022 10:23 am

.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:06 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 11:46 am

Rufus T. Firefly wrote:
DaveJfr0 wrote:
bob turner wrote:What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?


Yes, when I was trying to straighten it earlier, it clamps down straight cold just fine. I suppose I could cut down a sacrificial piece of plywood to throw in the boil. Gotta see if I have a pot big enough to hold this thing even tho its maybe 35-40'.


Maybe not throw it into the boil, but clamp or weight 1st, place in the bottom of a broiler pan,and then pour hot water into the pan - tea kettle works nicely. Last Henry-T kit I built had a nice curve to the floor; weighted it down onto a piece of 1/4" glass and poured hot water into the pan. Let it sit until cold. Worked great.


Okay, this seems less risky.

Curious, what did you use for weights and why did you need a piece of glass between it and the pan?

Tempted to see if anyone else on the other gatherings have ran into this issue with this manufacturer's castings...
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Bowed urethane castings - thoughts on a fix?

Postby Rufus T. Firefly » Mon Feb 14, 2022 12:16 pm

.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:06 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Bowed urethane castings - thoughts on a fix?

Postby E7 » Mon Feb 14, 2022 12:22 pm

JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Bowed urethane castings - thoughts on a fix?

Postby ScaleCraft » Mon Feb 14, 2022 1:02 pm

E7 wrote:JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.

Control may not be what you want. Everything I have read indicates even heating across the item, while clamping or weighting, allows stresses across the item to dissipate evenly.

Not sure point heat with a gun is optimal.
Dave....gone by invitation

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 1:05 pm

E7 wrote:JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.


Tried the heat gun. Think I made it worse. :-(

Gonna try this boil method sometime this week. It's a busy week already.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Bowed urethane castings - thoughts on a fix?

Postby ScaleCraft » Mon Feb 14, 2022 1:08 pm

DaveJfr0 wrote:Current status (Pre-boil):

Image


Image


Now that is interesting. Did not know you had a weight plate sandwiched in there. Surprisingly, the portion of the carbody with the weight seems fairly flat....it's right at the end of the weight it goes all wonky. What is the weight made of?

Any chance Zamac and it's expanding and pushing out right where it ends?
Dave....gone by invitation

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 1:20 pm

Pulled out the the ole instruction sheet to verify two materials:

Carbody made of polyurethane.

Weight is a custom-sheared piece of hot-rolled steel.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Bowed urethane castings - thoughts on a fix?

Postby Rufus T. Firefly » Mon Feb 14, 2022 2:00 pm

.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:07 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: Bowed urethane castings - thoughts on a fix?

Postby sarge » Mon Feb 14, 2022 2:10 pm

I really don't know why its a surprise. It's very clear the stiffness of the metal is perfectly suited for the purpose and I have never heard of a mix of metal and plastic being detrimental to stiffness or stability unless the metal is poorly controlled white metal gone with zincpest or lead shot poured in PVA, both of which expand.

That was the purpose of the suggestion that stiffening with brass will work (and it will). The issue is the instability of the polyurethane resin; fine in a box like a housecar, but will bow up as the sides of what is essentially a plate in this case shrink. It may relax with heat, but I'm not betting it will be any more stable unless stiffened with a much more predictable material. Steel appears to work.

Metal plate, rod, or tube cast within a plastic form or firmly attached to the outside for stiffening is mainstream outside of model building. It works just fine.

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 2:16 pm

Rufus T. Firefly wrote:
DaveJfr0 wrote:Weight is a custom-sheared piece of hot-rolled steel.


Glued in place?


Yes.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/

DaveJfr0
Posts: 401
Joined: Mon May 12, 2008 5:22 pm
Location: MD
Contact:

Re: Bowed urethane castings - thoughts on a fix?

Postby DaveJfr0 » Mon Feb 14, 2022 2:28 pm

sarge wrote:I really don't know why its a surprise. It's very clear the stiffness of the metal is perfectly suited for the purpose and I have never heard of a mix of metal and plastic being detrimental to stiffness or stability unless the metal is poorly controlled white metal gone with zincpest or lead shot poured in PVA, both of which expand.

That was the purpose of the suggestion that stiffening with brass will work (and it will). The issue is the instability of the polyurethane resin; fine in a box like a housecar, but will bow up as the sides of what is essentially a plate in this case shrink. It may relax with heat, but I'm not betting it will be any more stable unless stiffened with a much more predictable material. Steel appears to work.

Metal plate, rod, or tube cast within a plastic form or firmly attached to the outside for stiffening is mainstream outside of model building. It works just fine.


Hi Brian,

I want to make sure you know I didn't ignore your approach. Was just hoping to not perform invasive surgery if I can help it, which is why I started my focus with adding heat. All of the sill material is really thin, so I'm concerned that I may not be able to easily drill countersunk screws where needed without cracking the material or even having enough material to make a countersunk hole. Without an actual 0-80 or 2-56 countersinking bit, I'll have to be extremely careful.

Let me rule out the hot water method and if it doesn't work out, I'll give this approach a go if I don't ruin everything in the process.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 45 guests