The Tridaily Doorstop -- Bob's Mexicano Electric

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #4 Walthers PRR Boxcar

Postby R.K. Maroon » Fri Feb 11, 2022 12:51 am

Here is the title block from the drawing that came with the Walthers boxcar:
Image
The 1938 date is, I think, just past the "bronze age" at Walthers, so it is not surprising (but disappointing to me) that this one doesn't have the one-piece cast bronze frame:
Image
The car does, however, have the rare (and I think totally cool) Walthers sprung trucks:
Image
The only downside to these trucks is that they are soldered together, so you have to unsolder them to change wheelsets if they don't have insulated wheels, which is often the case.

Finally, here is the car as it appears in the 1940 catalog:
Image
The link below any photo will display the image full size

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: The Tridaily Doorstop -- #4 Walthers PRR Boxcar

Postby sarge » Fri Feb 11, 2022 6:24 am

You are interested in whether this might be the earliest version of the kit. There is an clue here that actually says perhaps not. My curiosity would be piqued by the notation that the 1938 drawing you have to hand supersedes previous versions.

Even if this single drawing replaces a set, which wouldn't surprise me given the near-sequential numeration of the superseded drawings, there is that notion of proof there was an earlier version of the kit. How early is, of course, an exercise left to the student.

Grin!

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby R.K. Maroon » Sat Feb 12, 2022 9:53 pm

# 5 -- Scale-Craft MP Stock Car

My favorite models of wood stock cars are themselves wood, but Alexander, Lobaugh, and Scale-Craft all offered cast metal stock cars in the years before the war, and I like them all just fine. Here is the Scale-Craft version:

Image

Image

The one shown was the first acquired. They must have been popular, as I have acquired a string of them without trying too hard. They weigh a bit under a pound and a half each, so pulling a string of these requires some oomph.
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby ScaleCraft » Sat Feb 12, 2022 11:07 pm

R.K. Maroon wrote:They must have been popular, as I have acquired a string of them without trying too hard. They weigh a bit under a pound and a half each, so pulling a string of these requires some oomph.


Like, oh, a sand-cast bronze doorstop locomotive.

Takes more work than one would think to make those "right" when assembling.
The gaps between boards usually are rough and full of casting over run.

LOTS of time with files...but worth it when done. Plus, you take the taper out, so the horizontal surfaces are actually horizontal.

Still, easier than the box of sticks Westbrooks.
Dave....gone by invitation

Dennis Holler
Posts: 474
Joined: Mon Dec 13, 2010 8:31 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby Dennis Holler » Sun Feb 13, 2022 10:41 am

I like those SC cattle cars, I only have one at this point and it needs a refresh but the castings are good. It's lighter than a Walthers boxcar with the LEAD cast ends IMO lmao. Pretty sure an SC Mountain would pull a string of them no issues. I realized have 12-15 SC reefer cars in various conditions and they too would make a neat consist behind the old Mountain.

I need to dig them out but I have three early Crestline reefers with the one pice cast fishbelly underframe. None of them bronze, think they are all Al. Also have a few of those Walthers sprung trucks and at least one pair of them with the ball bearing wheels... Those are weird lol. The Crestline fridge Blueprints are data Jan 31, 1939 and make no reference to previous versions yet these cars were shown in the 1936 catalog. Kit 3576(A) I have a Schlitz decaled reefer, but the builder really messed it up and scooted the door off center and same for the decals. Once you look at it closely it is puzzleing. All the wood boxcars I have have the built up underframe so I am curious if they used a solid on the regular boxcars at any point. I also have a couple of Crestlne early 3560 tank kits, and the 3500 cast gondola and an ealy Crestline hopper kit in a Brown box with simple white label on one end. Also have a couple of Mikado kit boxes that are plain brown like the hopper box. Not sure on the timing of the Brown boxes.I can get some pics if tehre is any interest for comparison. I'm also curious on the mix of Blueprint drawings versus black ink on white paper drawings for the kits.

Here is the Brown box Al hopper
Image
Doorstop Rookie

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby R.K. Maroon » Sun Feb 13, 2022 11:49 pm

Dennis mentioned trucks with ball bearings. Like the sprung trucks on the PRR boxcar, the trucks with ball bearings were short lived. I want to say neither lasted more than one catalog cycle, and, since they were an up charge, you don't see them often.

Here is the underside of the Scale-Craft stock car:
Image
The car has the later die-cast frame but is equipped with the all-white-metal trucks. By the time of the die-cast frame, Scale-Craft was offering trucks with a Bakelite bolster for two-rail operation. The presence of the white-metal trucks probably means the car was originally sold for outside third rail.
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby ScaleCraft » Mon Feb 14, 2022 1:06 am

R.K. Maroon wrote:The car has the later die-cast frame but is equipped with the all-white-metal trucks. By the time of the die-cast frame, Scale-Craft was offering trucks with a Bakelite bolster for two-rail operation. The presence of the white-metal trucks probably means the car was originally sold for outside third rail.

Not necessarily. Most of mine were metal bolsters....and only single insulated wheelsets.
Same wheelsets used on the Tenite or Bakelite bolster trucks.
You have to wonder...were they ALL OTR cars? Doubt it.
The problem with all of these is solid metal frame, metal bolsters and couplers.
String out 25-40 cars behind an engine, where the tender coupler is ONE polarity...you end up white dotting the front of each underbody to be "front", and a dot on one side of each frame bolster AND the truck bolster to match.

The fix is solid acrylic rod and 4d nails. Done a few, even fixes the shrinking bolster syndrome. Since they tend to shrink....and Bakelite does not have that propensity...Tenite.

BTW, OTR specific trucks were uninsulated. I have a wheelset flatcar loaded with uninsulated Auel wheelsets to prove the assertion!
Dave....gone by invitation

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby bob turner » Mon Feb 14, 2022 1:53 am

I prefer the older wheel contour. To that end, I gather the uninsulated Scale Craft wheelsets, make axles out of Plastruct tube and rod that I assume is close to #4 nails, and thus double insulate all my freight cars.

It requires a collet lathe to get the bore concentric and axial, and a press to maintain zero wobble - but it works for me.

I use the Scale Craft idea a lot too - just saw the axle in half, jam it into a Plastruct tube,and use Bakelite to separate the side frames. This trick allows all wheel pickup on tenders - really important for those plastic CLW drivered models.

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby R.K. Maroon » Mon Feb 14, 2022 11:13 pm

I should have been more clear. The catalogs indicate that in the early years, before the Bakelite bolster, the all-metal trucks, like the one on this model, were sold with Tenite wheels for two-rail operation. Insulated metal wheelsets came later., perhaps only when the Bakelite bolsters were introduced. I wrote an article on this so I'll go back and see what it says. Details notwithstanding, it is likely that these trucks were originally sold with either Tenite wheels or uninsulated wheels, and at some point the wheelsets were replaced with insulated wheelsets. Heck, I could have been the one to do it, but it was ten years ago and I have neither detailed records nor a good memory.

Here is the model as it appeared in the 1940 catalog:
Image
Note the road number is the same as the one on the car (52428). This must have been the decal number, it is quite common to see one with this same number.
The link below any photo will display the image full size

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby bob turner » Tue Feb 15, 2022 1:39 am

I think there were variants. The ones I have seen were lead casings, uninsulated steel wheels, Zamac castings/same, Zamac sideframes, plastic bolsters with metal end nails, wheels insulated at the center of the axle, and finally (not very often) wheels insulated from the axle.

User avatar
De Bruin
Posts: 991
Joined: Thu Jan 12, 2017 8:24 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby De Bruin » Tue Feb 15, 2022 9:15 pm

R.K. Maroon wrote:Dennis mentioned trucks with ball bearings. Like the sprung trucks on the PRR boxcar, the trucks with ball bearings were short lived. I want to say neither lasted more than one catalog cycle, and, since they were an up charge, you don't see them often.....

Yes he did,
Image
these were on a pretty ancient Railcraft gondola at the downtown club, the outer wheel faces have gotten so laterally sloppy with the "race" on the inside of the wheel hubs that they regularly pick switches.
Image
Are these the ball bearing trucks you guys refer to here?
Image
No longer useful but almost too weird to throw away either.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com

Dennis Holler
Posts: 474
Joined: Mon Dec 13, 2010 8:31 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby Dennis Holler » Wed Feb 16, 2022 7:19 am

Think those are them... Will dig mine out lol. You could squirt some super glue in them and make them solid, wobbly, wheels :mrgreen:

Thinking about pressing off some of the tinplate Auel whells I have and trying to turn them down to match the Auel scale profile..... Might be amusing... they might just crumble too lmao...
Doorstop Rookie

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby R.K. Maroon » Wed Feb 16, 2022 8:32 pm

Those look like the ball-bearing trucks I have seen. I am out of town for a couple of days but will check when I get back.

Jim
The link below any photo will display the image full size

User avatar
De Bruin
Posts: 991
Joined: Thu Jan 12, 2017 8:24 pm

Re: The Tridaily Doorstop -- #5 Scale-Craft MP Stock Car

Postby De Bruin » Wed Feb 16, 2022 11:43 pm

Dennis Holler wrote:Think those are them... Will dig mine out lol. You could squirt some super glue in them and make them solid, wobbly, wheels....


Yeah, I spend a lot of time in old freight car hell these I'll pass.... :wink:
BTW that cast double door X-31 of yours is very cool...and certainly worth cleaning up to a maximum appearance,
whoops! more old freight car hell....like a moth to a flame apparently.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #6 Alexander PRR Tank Car

Postby R.K. Maroon » Thu Feb 17, 2022 9:13 pm

# 6 -- Alexander PRR Tank Car

Wood-dowel tank cars were fairly common before the war. Here is one from Alexander:
Image
Image
This tank car probably started life with a printed cardboard wrapper with Texaco markings on it. I don't know that I have ever seen one of these cars with its wrapper in serviceable condition. One would image then that some modeler gave up on the wrapper but not the car. Works for me.

Jim
The link below any photo will display the image full size


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 51 guests