Bowed urethane castings - thoughts on a fix?
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Bowed urethane castings - thoughts on a fix?
What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?
Re: Bowed urethane castings - thoughts on a fix?
bob turner wrote:What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?
Yes, when I was trying to straighten it earlier, it clamps down straight cold just fine. I suppose I could cut down a sacrificial piece of plywood to throw in the boil. Gotta see if I have a pot big enough to hold this thing even tho its maybe 35-40'.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
Re: Bowed urethane castings - thoughts on a fix?
Current status (Pre-boil):


Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
- Rufus T. Firefly
- Posts: 42237
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Bowed urethane castings - thoughts on a fix?
.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:06 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Bowed urethane castings - thoughts on a fix?
Rufus T. Firefly wrote:DaveJfr0 wrote:bob turner wrote:What if you clamp it to a board first, then boil it? Can it be forced straight cold with clamps?
Yes, when I was trying to straighten it earlier, it clamps down straight cold just fine. I suppose I could cut down a sacrificial piece of plywood to throw in the boil. Gotta see if I have a pot big enough to hold this thing even tho its maybe 35-40'.
Maybe not throw it into the boil, but clamp or weight 1st, place in the bottom of a broiler pan,and then pour hot water into the pan - tea kettle works nicely. Last Henry-T kit I built had a nice curve to the floor; weighted it down onto a piece of 1/4" glass and poured hot water into the pan. Let it sit until cold. Worked great.
Okay, this seems less risky.
Curious, what did you use for weights and why did you need a piece of glass between it and the pan?
Tempted to see if anyone else on the other gatherings have ran into this issue with this manufacturer's castings...
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
- Rufus T. Firefly
- Posts: 42237
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Bowed urethane castings - thoughts on a fix?
.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:06 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Bowed urethane castings - thoughts on a fix?
JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: Bowed urethane castings - thoughts on a fix?
E7 wrote:JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.
Control may not be what you want. Everything I have read indicates even heating across the item, while clamping or weighting, allows stresses across the item to dissipate evenly.
Not sure point heat with a gun is optimal.
Dave....gone by invitation
Re: Bowed urethane castings - thoughts on a fix?
E7 wrote:JMHO, But if you have a heat gun, I'd clamp it flat and take that to it. I'd guess you would have better control with that than boiling or an oven.
Tried the heat gun. Think I made it worse.
Gonna try this boil method sometime this week. It's a busy week already.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: Bowed urethane castings - thoughts on a fix?
DaveJfr0 wrote:Current status (Pre-boil):
Now that is interesting. Did not know you had a weight plate sandwiched in there. Surprisingly, the portion of the carbody with the weight seems fairly flat....it's right at the end of the weight it goes all wonky. What is the weight made of?
Any chance Zamac and it's expanding and pushing out right where it ends?
Dave....gone by invitation
Re: Bowed urethane castings - thoughts on a fix?
Pulled out the the ole instruction sheet to verify two materials:
Carbody made of polyurethane.
Weight is a custom-sheared piece of hot-rolled steel.
Carbody made of polyurethane.
Weight is a custom-sheared piece of hot-rolled steel.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
- Rufus T. Firefly
- Posts: 42237
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Bowed urethane castings - thoughts on a fix?
.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 8:07 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Bowed urethane castings - thoughts on a fix?
I really don't know why its a surprise. It's very clear the stiffness of the metal is perfectly suited for the purpose and I have never heard of a mix of metal and plastic being detrimental to stiffness or stability unless the metal is poorly controlled white metal gone with zincpest or lead shot poured in PVA, both of which expand.
That was the purpose of the suggestion that stiffening with brass will work (and it will). The issue is the instability of the polyurethane resin; fine in a box like a housecar, but will bow up as the sides of what is essentially a plate in this case shrink. It may relax with heat, but I'm not betting it will be any more stable unless stiffened with a much more predictable material. Steel appears to work.
Metal plate, rod, or tube cast within a plastic form or firmly attached to the outside for stiffening is mainstream outside of model building. It works just fine.
That was the purpose of the suggestion that stiffening with brass will work (and it will). The issue is the instability of the polyurethane resin; fine in a box like a housecar, but will bow up as the sides of what is essentially a plate in this case shrink. It may relax with heat, but I'm not betting it will be any more stable unless stiffened with a much more predictable material. Steel appears to work.
Metal plate, rod, or tube cast within a plastic form or firmly attached to the outside for stiffening is mainstream outside of model building. It works just fine.
Re: Bowed urethane castings - thoughts on a fix?
Rufus T. Firefly wrote:DaveJfr0 wrote:Weight is a custom-sheared piece of hot-rolled steel.
Glued in place?
Yes.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
Re: Bowed urethane castings - thoughts on a fix?
sarge wrote:I really don't know why its a surprise. It's very clear the stiffness of the metal is perfectly suited for the purpose and I have never heard of a mix of metal and plastic being detrimental to stiffness or stability unless the metal is poorly controlled white metal gone with zincpest or lead shot poured in PVA, both of which expand.
That was the purpose of the suggestion that stiffening with brass will work (and it will). The issue is the instability of the polyurethane resin; fine in a box like a housecar, but will bow up as the sides of what is essentially a plate in this case shrink. It may relax with heat, but I'm not betting it will be any more stable unless stiffened with a much more predictable material. Steel appears to work.
Metal plate, rod, or tube cast within a plastic form or firmly attached to the outside for stiffening is mainstream outside of model building. It works just fine.
Hi Brian,
I want to make sure you know I didn't ignore your approach. Was just hoping to not perform invasive surgery if I can help it, which is why I started my focus with adding heat. All of the sill material is really thin, so I'm concerned that I may not be able to easily drill countersunk screws where needed without cracking the material or even having enough material to make a countersunk hole. Without an actual 0-80 or 2-56 countersinking bit, I'll have to be extremely careful.
Let me rule out the hot water method and if it doesn't work out, I'll give this approach a go if I don't ruin everything in the process.
Focus: 2R O-Scale, SOU/SCL 1967-1972
Blog: http://davejfr0.blogspot.com/
Blog: http://davejfr0.blogspot.com/
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 31 guests