The Tridaily Doorstop -- Bob's Mexicano Electric

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby bob turner » Tue Mar 01, 2022 1:54 pm

Yes. I remember somebody calling it that:

Image

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby Rufus T. Firefly » Tue Mar 01, 2022 2:41 pm

.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 5:09 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby R.K. Maroon » Tue Mar 01, 2022 10:51 pm

Bob pointed out that the tender has rivets, implying that the original model did not. He is correct, as this tender from a similar model, not owned by me, shows:

Image

Not surprisingly, this is a tender drive locomotive:

Image

The Pittman open-frame PM motor is not original. Like most (or all?) pre-war models, these came with a wound-field motor.

Here is an underside shot of engine and tender:

Image

That massive chassis frame around the drivers is not likely to be original. Here is a similar shot from the other model:

Image

I don't know Jerry White's work well enough to know whether this has his fingerprints on the NYC model or not. It does run well though. I will look to see if I have any video of it on the layout.

Jim
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby ScaleCraft » Tue Mar 01, 2022 11:22 pm

Boy, flipping back and forth between those two chassis shots, not a lot is the same. Drawbar mount, firebox/ashpan, cylinders totally different, of course the frame, lead truck, lack of dummy Stephenson's on one, different crosshead supports. Almost not an Alexander, especially with rivetted tender. Odd. Nice, but odd.
Dave....gone by invitation

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby Rufus T. Firefly » Wed Mar 02, 2022 9:18 am

.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 5:09 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby ScaleCraft » Wed Mar 02, 2022 12:23 pm

It is nice to see smaller steam, yet bigger than Thomas 0-4-0's!

I would really like to see some more shots of the unmolested one. The nice NYC appears to be basically all new, can't tell on boiler shape as I have no comparison photos, but the small bit of the unmolested cab shows what I would expect, sand cast bronze. The NYC appears to be straight, smooth, sharp corners, like build up.
There must have been prototype concerns for builder to machine out a chunk of something solid for his new chassis, instead of using the see-through framework. Even the main rod details have been removed.
One of those things you wake up in the middle of the night and say "Huh?"
Dave....gone by invitation

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby ScaleCraft » Wed Mar 02, 2022 12:39 pm

ScaleCraft wrote:It is nice to see smaller steam, yet bigger than Thomas 0-4-0's!

I would really like to see some more shots of the unmolested one. The nice NYC appears to be basically all new, can't tell on boiler shape as I have no comparison photos, but the small bit of the unmolested cab shows what I would expect, sand cast bronze. The NYC appears to be straight, smooth, sharp corners, like build up.
There must have been prototype concerns for builder to machine out a chunk of something solid for his new chassis, instead of using the see-through framework. Even the main rod details have been removed.
One of those things you wake up in the middle of the night and say "Huh?"


A little research and speculation.
Mayhaps Mister Alexander made multiple versions of the 4-4-0. Here is an alleged NYC 4-4-0 by Alexander. Let's say, under speculation mode, for early units, bronze boilers and cabs for weight...later, built up brass boilers and cabs, no weight, design that big block chassis.
Image


Of course, without and clarification as to WHAT he is showing, here is Ed holding a 4-4-0:
Image
Dave....gone by invitation

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby bob turner » Wed Mar 02, 2022 10:52 pm

Lobaugh, mostly:

Image

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby R.K. Maroon » Wed Mar 02, 2022 11:09 pm

Nice model, Bob. I had one of the Lobaughs once, but a friend valued it more as a collectible than I did as an operating model, so it went to him.

I appreciate Dave's comments and the time he spent to study the photos I posted carefully. The NYC 4-4-0 was sold to me a long time ago as an Alexander. I never questioned it as, at a quick glance, it looked about right. Now I am beginning to question how much, if any, of the NYC 4-4-O is Alexander. Here are some photos to make things easier to compare. First, the model as shown in the 1937 AMRACO catalog:

Image

Now, the NYC version (sorry, no direct side photo in hand):

Image

Next, the other known model (sorry, no shot of the engineer's side):

Image

Here is a photo of a magazine ad showing the fireman's side and indicating that boiler is cast and the prototype is M&StL:

Image

Note as an aside that Alexander cataloged two 4-4-0s in 1937. The other was listed as an "old timey" PRR "P" (D13c):

Image

I have never seen one that I know of.

Jim
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby ScaleCraft » Thu Mar 03, 2022 12:17 am

Gets worse, doesn't it? Domes are different, cowcatcher different, taper of the boiler at bell LOOKS to be WAY off, stack and headlight different, length of the side sheets for coal totally different in length, length of pilot beam from smokebox front, firebox side sheets, looks like smokebox support rods, original cab is cast, your NYC version looks thinner brass sheet...add to the HUGE differences in chassis, probably a Jim Fitzhugh model from 1939.
Dave....gone by invitation

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby bob turner » Thu Mar 03, 2022 1:51 am

"Probably" is a strong word to use without some slight evidence. There are quite a few modelers capable of most of that work. I would have to study that tender a bit more closely - Rod Miller has Gerry's rivet machine, and that may be the absolute best rivet embosser anywhere.

My rivets get done one at a time, and I often miss a beat or get a raised area around an end rivet. I see none of that on the tender above.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #9 Alexander NYC 4-4-0

Postby ScaleCraft » Thu Mar 03, 2022 12:17 pm

bob turner wrote:"Probably" is a strong word to use without some slight evidence. There are quite a few modelers capable of most of that work. I would have to study that tender a bit more closely - Rod Miller has Gerry's rivet machine, and that may be the absolute best rivet embosser anywhere.

My rivets get done one at a time, and I often miss a beat or get a raised area around an end rivet. I see none of that on the tender above.

*snicker*.
I HOPE you're referring to my "probably Jim Fitzhugh" comment.
You know, the guy born on Oklahoma....moved to an island in the Okefenokee Swamp. Had to transport all supplies in and product out by an airboat or a fan boat, plane boat, swamp boat, bayou boat, you know.
Inducted into the RMR Hall of Shame?
But maybe it's Tyson McGillicudy out of West Skookum, Virginia.
Dave....gone by invitation

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

The Tridaily Doorstop -- #10 Scale-Craft SFRD (Santa Fe) Reefer

Postby R.K. Maroon » Thu Mar 03, 2022 10:02 pm

#10 -- Scale-Craft SFRD (Santa Fe) Reefer

This Scale-Craft reefer is one of the first doorstop freight cars I ever bought:

Image

Image

This was May of 2012, and my interest in old models had just started. My records indicate I paid $4.13 plus $10 shipping for this reefer. My notes in the record state, "maybe the best deal ever". I don't know about that, but I'd take them all day at that price now, if they were in the same condition.
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop -- #10 Scale-Craft SFRD (Santa Fe) Reefer

Postby ScaleCraft » Thu Mar 03, 2022 11:19 pm

Don't tell Martin! He'll lump you in with me on my "never spent more than ten bucks" category!
Dave....gone by invitation

Dennis Holler
Posts: 474
Joined: Mon Dec 13, 2010 8:31 pm

Re: The Tridaily Doorstop -- #10 Scale-Craft SFRD (Santa Fe) Reefer

Postby Dennis Holler » Fri Mar 04, 2022 8:26 am

Ha, That same car was also one of my first doorstop car purchases... I think my very first one was Thomas single dome tank. Your's maybe postwar or the later Thomas ownership with that slogan on the side as I presume the pre 1940 cars did not include the slogan.... Then again, looking at your photo's, your car seems to have the earlier frame so who knows lol. I have noticed the later frame is a fraction wider and will not actually fit the early built up cars.
Image
And a WP I got at the same time, both decently built I think at least decent enough for me lol.
Image
I should have shopped out that middle rail lmao.
Image

You def for the most part can't get away with tunning box stock scalecraft cars and trucks on three rail track with the stock thruck mounting pins that came with the cars lmao
Doorstop Rookie


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: Carey Williams and 39 guests