Tractor Thread

Play nice and have fun... AS OF JULY 12 2025, THIS FORUM IS LOCKED.
User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Tractor Thread

Postby Rufus T. Firefly » Wed Sep 02, 2015 7:33 am

healey36 wrote:.......... we sure could stand some rain.


Yes. After all that rain we had early in the summer, things are turning brown now......
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

The Dirt
Posts: 3067
Joined: Sun Jun 24, 2007 2:54 pm
Location: Orangeville, Pa.

Re: Tractor Thread

Postby The Dirt » Wed Sep 02, 2015 1:59 pm

There's been so many of you sending me PMs asking me..

1) How do a Farmall 450's brakes work?
2) How are they different from a car?

... that I took off the brake housing to demonstrate.

Here's the housing looking at it as though you were inside the final-drive case.
The arrow points to the articulated arm on which the brake arm pulls, (the dust boot removed).
Top layer is one of the two discs, which bears on a wear surface on the final-drive case, and a wear-surface on the 'actuator' beneath..

Image

Next layer is the actuator, consisting of two plates, constrained by three lugs cast into the housing. As the articulated arm is pulled, the upper plate rotates clockwise, the lower plate counter-clockwise, their motion limited by the 'dog' on each plate, the limits of travel shown by the arrows.
If, in moving that distance, the discs don't engage their respective wear-surfaces, you have no brakes. The adjustment of such will be described later.

Image

Next layer is the outer (relative to the tractor) disc.

Image

Finally, the wear-surface of the housing, (with a nice mirror finish).

Image

Here, the actuator assembly. The two plates are constrained to each other, and made to move to their 'home' positions, by 3 strong springs that connect the plates via the 3 sets of lugs on their inner diameters.
The plate wear-surface is uneven, but this is a tractor and not a race-car, and I've been assured, on a tractor forum, that neither pits nor unevenness are an issue, and all that need be done is to remove the glaze from all four wear-surfaces.

Image

A quick demonstration, via a pull on the articulated arms. At rest...

Image

... and under tension, where one can see 1) that they have rotated respective to each other, and 2) that they have gained distance between them, which is the motion that causes the discs to bear against their wear-surfaces.

Image

Lastly, the cause of the plates moving apart... 5 steel balls with ramps. The spring pressure cause them to climb the ramps rather than spin in-place.

Image

The adjustment of tolerance is pretty primitive. Once everything is cleaned, all glazes of wear-surfaces and discs carefully sanded in radial directions, carefully and lightly lubed on metal-to-metal surfaces, and restacked in the housing, there should be .030" to .060" distance between the top disc, and a straightedge placed across the face of the housing. If the clearance is too large (even .100 being too much), the clearance is reduced by milling the proper amount off the face of the housing. No other way to do it.

The difference from a car, of course, is that on a car, the wear-surfaces rotate and the 'pads' are stationary. On the 450, the roles are reversed.

And there you have it.
Now everyone can sleep peacefully tonight.
You're welcome.

:wink: :roll: :D

User avatar
rogruth
Posts: 24452
Joined: Sun Aug 14, 2005 8:32 pm
Location: pembroke,ga

Re: Tractor Thread

Postby rogruth » Wed Sep 02, 2015 3:09 pm

Pete,

I'm not sure I could do it but I think I understand it.
The doohickey pushes on the thingamajig that rubs against the whatchamacallit and makes it stop.

Seriously,I do think I understand.The sentence just above is how an uncle would have explained it.
He knew exactly what he was saying and could fix all kinds of stuff. His explanation for what he did
would always be similar to the doohickey stuff.

You probably know somebody just like him. :D
roger

I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH

User avatar
healey36
Posts: 7026
Joined: Fri Sep 03, 2010 4:43 pm
Location: Westminster, MD

Re: Tractor Thread

Postby healey36 » Wed Sep 02, 2015 5:56 pm

Wow...all I had to do was whine a bit here on MTJ and lookie...it's raining!

Image

Healey

User avatar
healey36
Posts: 7026
Joined: Fri Sep 03, 2010 4:43 pm
Location: Westminster, MD

Re: Tractor Thread

Postby healey36 » Wed Sep 02, 2015 6:20 pm

There's always some joker in the neighborhood trying to muscle-up on everyone else...biggest pool, biggest BBQ grille, biggest SUV, biggest ATV:

Image

What the...we're going to need that Scorpion, Sarge...

Healey

User avatar
Mitch
Posts: 5215
Joined: Sat May 28, 2005 2:06 pm
Location: Freeport, Pa.

Re: Tractor Thread

Postby Mitch » Wed Sep 02, 2015 6:36 pm

healey36 wrote:Wow...all I had to do was whine a bit here on MTJ and lookie...it's raining!

Healey


We could use a little rain here; it's been drier than a popcorn fart! One good thing is that the yard is already burned up, so we don't need to mow. But a good old fashioned thunderstorm would be nice. I need to gather up some nightcrawlers 'cause I'm gonna take a weeks' vacation starting the 14th, and I wanna do some fishin'. :wink: :lol:
If you agree with the Progressives, it's freedom of speech. If you disagree, it's hate speech. There are no alternatives.

User avatar
Rufus T. Firefly
Posts: 42237
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Tractor Thread

Postby Rufus T. Firefly » Wed Sep 02, 2015 6:40 pm

Mitch wrote:
healey36 wrote:Wow...all I had to do was whine a bit here on MTJ and lookie...it's raining!

Healey


We could use a little rain here....


We had plenty of thunder, darkness, and then the sprinking can goy upturned for a few minutes - all flash and no show.....
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
robert.
Posts: 6010
Joined: Mon Mar 02, 2015 9:24 am

Re: Tractor Thread

Postby robert. » Wed Sep 02, 2015 8:17 pm

Mitch wrote:
healey36 wrote:Wow...all I had to do was whine a bit here on MTJ and lookie...it's raining!

Healey


We could use a little rain here; it's been drier than a popcorn fart! One good thing is that the yard is already burned up, so we don't need to mow. But a good old fashioned thunderstorm would be nice. I need to gather up some nightcrawlers 'cause I'm gonna take a weeks' vacation starting the 14th, and I wanna do some fishin'. :wink: :lol:

you can shock out the worms. Use an old electric cord. Cut off the female end. Separate the 2 wires. Attach a screwdriver to each side .Water the yard at dark for 20 minutes. Turn off water and place screwdrivers 5 feet apart in wet soil.Plug the cord in. Nightcrawlers. will dance to the surface. https://www.youtube.com/watch?v=hugjPKD36wM
I spend entirely too many hours a day tying my shoes

User avatar
Mitch
Posts: 5215
Joined: Sat May 28, 2005 2:06 pm
Location: Freeport, Pa.

Re: Tractor Thread

Postby Mitch » Wed Sep 02, 2015 9:03 pm

Too much like work, Robert. Not to mention the destruction of a perfectly good extension cord and driving screwdrivers into the yard, which is nothing but baked clay. Much easier to just go out and pick them up an hour after a thunder shower.
If you agree with the Progressives, it's freedom of speech. If you disagree, it's hate speech. There are no alternatives.

The Dirt
Posts: 3067
Joined: Sun Jun 24, 2007 2:54 pm
Location: Orangeville, Pa.

Re: Tractor Thread

Postby The Dirt » Thu Sep 03, 2015 6:00 pm

Wow...all I had to do was whine a bit here on MTJ and lookie...it's raining!

Not what your wife said.
She said something about you being in the backyard with feathers and a loincloth doing a Hopi rain dance.
Don't MAKE me post the picture she sent.

User avatar
healey36
Posts: 7026
Joined: Fri Sep 03, 2010 4:43 pm
Location: Westminster, MD

Re: Tractor Thread

Postby healey36 » Thu Sep 03, 2015 6:07 pm

It was working until the loin-cloth got caught on her damn roses...that's when it got really ugly.

Hey, what's up with the Chinese and pixelated camo...is this the latest thing or am I behind the times?

Image

Image

Designed to play havoc with your Magnovox range-finder?

Healey

User avatar
robert.
Posts: 6010
Joined: Mon Mar 02, 2015 9:24 am

Re: Tractor Thread

Postby robert. » Thu Sep 03, 2015 6:19 pm

healey36 wrote:
Image

Designed to play havoc with your Magnovox range-finder?

Healey

i bet they stick out like a sore thumb to the naked eye.
I spend entirely too many hours a day tying my shoes

User avatar
robert.
Posts: 6010
Joined: Mon Mar 02, 2015 9:24 am

Re: Tractor Thread

Postby robert. » Thu Sep 03, 2015 6:32 pm

It has been a summer of strays following me home. I got this yamaha rd 350 last week. i'm just waiting for a trucking friend to pick it up at another friends house. Anyway when i'm done with the build it. the rusty bike will look like the nice little racer. I keep you guys posted on the build. Builds like this have been played out a million times on the 2 stroke threads. They kind of tire from them. There is a lot of life left in that rusty bike. The motor is stuck and needs a rebuild. That's fine with me. It keep the price down. i paid less for this then what most people pay to get a new tittle for an old bike. While i'm at it i'll gives you some insight on how a 2 stroke works. Plus how to make one stand up and dance. stay tuned.

Image
Image
I spend entirely too many hours a day tying my shoes

User avatar
healey36
Posts: 7026
Joined: Fri Sep 03, 2010 4:43 pm
Location: Westminster, MD

Re: Tractor Thread

Postby healey36 » Thu Sep 03, 2015 6:50 pm

robert. wrote:
healey36 wrote:
Image

Designed to play havoc with your Magnovox range-finder?

Healey

i bet they stick out like a sore thumb to the naked eye.


Those in the know tell me this is a naval scheme...on a tank...very innovative.

Looking forward to seeing the Yamaha progression...

User avatar
MurphOnMillerAve
Posts: 18489
Joined: Fri Jul 18, 2008 10:18 pm
Location: Kennywood Park
Contact:

Re: Tractor Thread

Postby MurphOnMillerAve » Thu Sep 03, 2015 7:51 pm

...but what are they getting ready for?
"Doing wrong is like a joke to a fool." Proverbs 10: 21-28


Return to “The Club Car Lounge”

Who is online

Users browsing this forum: No registered users and 60 guests